manualshive.com logo in svg

TROY XCD MAN-EXT2000, Administrator'S Manual, Page: 210 / 252

Share
Download
TROY XCD MAN-EXT2000 Administrator'S Manual Download Page 210

A-8   Command Summary

SET LOCaltalk [EN|DIS]

Enables/disables LocalTalk port

SET APpletalk [EN|DIS]

Enables/disables Appletalk processing

SET SERVIce <servicename> APP [EN|DIS]

Enables or disables AppleTalk jobs on specified service

SET SERVIce <servicename> RECEIVE [EN|DIS]

Enables or Disables bidirectional communications on service.

SHow APpletalk

Shows AppleTalk parameters

SHow LOCaltalk

Shows LocalTalk parameters

Banyan VINES Commands

CLEAR BANYAN PAssword <password>

Clears Banyan login password

CLEAR SERVIce <servicename> STreettalk

Disables the Banyan protocol on the specified  service.

SET BANyan LOgin <loginname>

Sets StreetTalk login name of print server.

SET BANyan PAssword <password>

Sets login password of print server.

SET SERVIce <servicename> STreettalk <queuename>

Enables the Banyan protocol on the specified print server service and
associates this service with the StreetTalk name of a given print queue
the VINES file server.

SET BANyan HOp nn

Sets  number of hops between the print server and the Banyan file server
(default value is 2).

Summary of Contents for MAN-EXT2000





























































































































































































































































Reviews:

No comments