5
Stand
Trigger Lock
Starter Rope
Handle
Waist Support
Clip
Muffler
Air Filter Cover
KNOW YOUR UNIT
Primer Bulb
Suspension System
Fuel Tank
Choke Lever
Waist Support
Fuel
Cap
Trigger
Blower Tube
Shoulder Support Buckle
Throttle Grip
Throttle Cables
Nozzle
ASSEMBLY INSTRUCTIONS
ASSEMBLING THE BLOWER TUBE
Installing the Flex Tube
1.
Place a hose clamp over the end of the Flex Tube (Fig. 1A).
2.
Slide the end of the Flex Tube with the clamp on it over the
elbow tube (Fig. 1B).
3.
Align the bump on the Flex Tube with the bump on the elbow
tube (Fig. 1C).
4.
Tighten the screw on the hose clamp to secure the Flex Tube
to the elbow tube (Fig. 1D).
Installing the Upper Blower Tube
1.
Place a hose clamp over the other end of the Flex Tube (Fig.
2, A).
2.
Slide the end of the hose with the clamp on it over the top
end of the upper blower tube (Fig. 2, B).
3.
Align the bump on the Flex Tube with the bump on the upper
blower tube (Fig. 2, C).
4.
Tighten the screw on the hose clamp to secure the Flex Tube
to the upper blower tube (Fig. 2, D).
Installing the Lower Blower Tubes and Nozzle
1.
Align the bump slot on the end of the first lower blower tube
with the bump on the bottom end of the upper blower tube
(Fig. 3, A).
2.
Insert the bump on the upper blower tube into the bump slot
on the tube extension (Fig. 3, A).
3.
Twist the extension tube clockwise around the upper upper
blower tube until the handle tube bump locks into place (Fig.
3, B).
4.
Align the bump slot on the end of the second lower blower
tube with the bump on the bottom end of the first lower
blower tube (Fig. 4, A).
5.
Insert the bump on the first lower blower tube into the bump
slot on the second lower blower tube (Fig. 4, A).
6.
Twist the second lower blower tube clockwise around the first
lower blower tube until the second lower blower tube bump
locks into place (Fig. 4, B).
7.
Align the bump slot on the top end of the nozzle with the bump on the bottom end of the second
lower blower tube (Fig. 5, A).
Fig. 1
B
A
D
C
Fig. 2
B
A
D
C
WARNING:
To avoid serious personal injury
and damage to the unit, shut the unit off before
removing or installing the blower tubes.
A
B
Fig. 3
Shoulder Support
Fig. 6
Adjusting the Handle
1.
Rotate the throttle grip counterclockwise around the blower tube
until it is pointing directly downward (Fig. 8, A).
2.
Pull or push the throttle grip along the handle tube until its
distance from the backpack blower is comfortable (Fig. 8, B).
3.
Align the throttle grip with the slot closest to the comfortable
place and rotate the throttle grip clockwise into the upright
position (Fig. 9).
Flex Tube
Hose Clamp
Elbow Tube
Upper Blower Tube
First Lower Blower
Tube
Second Lower Blower
Tube
Nozzle
Throttle Cables
Hose Clamp
Throttle Grip
On/Off Switch
Fig. 8
A
Fig. 9
B
8.
Insert the bump on the second lower blower tube into the bump slot on the nozzle (Fig. 5, A).
9.
Twist the nozzle clockwise around the second lower blower tube until the nozzle bump locks into
place (Fig. 5, B).
Fig. 4
A
Fig. 5
B
A
B
Secure the Throttle Cables
Place a zip tie around the elbow tube and the throttle cables
(Fig. 7) as shown, making sure not to crimp the cables.
The completed blower tube should look like Figure 6.
Fig. 7
Zip Tie
Zip Tie
WARNING:
Do not rotate the handle clockwise
to adjust. This may cause the throttle cables to
disconnect from the throttle grip or the engine.
WARNING:
To avoid serious personal injury, make sure that all four parts of the
blower tube are locked in place or firmly installed.
Summary of Contents for TB2BP
Page 27: ...E11 NOTES ...