background image

13

Fig. 17

Indexing Teeth

Holding Slots

Fig. 18

Slot

Split Wall

Fig. 19

Top Hole

Bottom Hole

Split

Wall

Fig. 20

Holding

Slots

Fig. 21

Outer Spool

Bump Knob

Inner Reel

Spring

Eyelets

Part 2 - Winding New Trimming Line onto the Inner Reel
• If using single line, refer to Winding Single Line.
• If using split line, refer to Winding Split Line.
• If using a prewound inner reel, proceed to Part 3 - Installing the

Inner Reel.

Winding Single Line
1. Cut one 12-foot (3.7 m) length of new single trimming line. Fold

the line in half to create a loop in the middle.

2. Insert the loop into the slot in the split wall (Fig. 18). Wind the

line tightly in the direction shown on the bottom of the inner reel

until about 6 inches (150 mm) of line remains. Keep the top half

of the line above the split wall and the bottom half of the line

below the split wall. 

3. Insert the two 6-inch sections into the two .095 holding slots

(Fig. 20).

NOTE: Failure to wind the line in the direction indicated will cause

the cutting head to operate incorrectly.

Proceed to Part 3 - Installing the Inner Reel.

Winding Split Line
1. Cut one 6-foot (1.8 m) length of new split line trimming line. Split

each end about 6 inches (150 mm). 

2. Using one split end, insert one line into the top hole and the

other line into the bottom hole in the inner reel (Fig. 19).

3. Wind the line tightly in the direction shown on the bottom of the

inner reel. The split wall will automatically divide the line. Wind

the line until it is completely divided and about 6 inches (150

mm) of line remains. 

NOTE: Failure to wind the line in the direction indicated will cause

the cutting head to operate incorrectly.

4. Insert the two 6-inch sections into the two .095 holding slots

(Fig. 20). 

Proceed to Part 3 - Installing the Inner Reel.

Part 3 - Installing the Inner Reel
1. Pass the two line ends through the eyelets in the outer spool.

Place the spring inside the inner reel. Insert the inner reel into

the outer spool. Push the inner reel and outer spool together

(Fig. 21). 

NOTE: The spring must be assembled on the inner reel before

reassembling the cutting head.

2. While holding the inner reel and outer spool together, firmly pull

the two line ends to release them from the holding slots.

3. While holding the inner reel and outer spool together, screw the

bump knob on clockwise. Tighten the bump knob securely.

Summary of Contents for TB22









































Reviews: