background image

10

S

ection

 5 — M

aintenance

 & S

ervice

4. 

Remove the front wheel bracket by loosening 

the four flange nuts (and hex bolts). Retain 

hardware. See Figure 5-14.

Figure 5-14

5. 

Remove six flange nuts which secure hopper 

inlet guide to impeller housing. See Figure 5-15

.

Figure 5-15

6. 

Carefully separate the hopper assembly from 

the impeller housing and set it aside.

7. 

Insert a piece of wood into the chute deflector 

opening to stabilize the impeller and prevent 

it from rotating when removing the shredder 

blade.

8. 

Remove the hex bolt, flat washer, and 

spacer to completely free shredder blade.                            

See Figure 5-16.

Figure 5-16

9. 

Install a replacement blade (Part No. 742-

05239) with the hardware removed earlier.  

See Figure 5-17.

Figure 5-17

IMPORTANT: 

When reassembling the blade, 

tighten center bolt to between 31 ft.-lbs and 

35 ft.-lbs. Also, make sure that the blade is 

pushed against the impeller vane.

Clutch Bumpers

It is necessary to check the clutch bumpers, installed 

on the dog clutch assembly, before each use.  The 

clutch bumpers are wearable parts that will need to 

be replaced periodically after extended usage.
To replace the clutch bumpers, follow these 

instructions:
1. 

Gently pry each clutch bumper out of the 

dog clutch using a standard screw driver.             

See Figure 5-18.

Figure 5-18

2. 

Replace the clutch bumpers (Kit Part No. 753-
08457) by fully pressing them into place.

Off-Season Storage

• 

Allow the unit to run and clear out all debris 

for a short time before shutting the unit down 

before storage.

• 

When storing the chipper shredder in an 

unventilated or metal storage shed, care 

should be taken to rustproof the non-painted 

surfaces. Using a light oil or silicone, coat the 

equipment, especially any springs, bearings, 

and cables.

• 

Remove all dirt from exterior of equipment.

• 

Follow lubrication recommendations.

• 

Store equipment in a clean, dry area. Do not 

store in an area where equipment is present 

that may use a pilot light or has a component 

that can create a spark.

Drive Belt

IMPORTANT: 

See an authorized service dealer to 

have your belt replaced.

Summary of Contents for FLEX Chipper Shredder

























Reviews: