Troy-Bilt 52063, 52064 Owner'S Manual Download Page 22

Page: 22 / 24

Parts List

Model 52063 & 52064

DRAWING NO. 2

See DRAWING

NO. 1

See DRAWING

NO. 3

See ACCESSORIES

AND KITS

8
9

1917778

Wheel/Tire Assembly..............................

1917593

Locking Retaining Ring ..........................

1917775

Flat Washer ............................................

1917258

Axle ........................................................

1918069

Self-Tap Screw, 5/16-18 x 2...................

1917588

Cap Plug.................................................

1734514

Hex Lock Nut, 1/2-13 .............................

9928

Belleville Washer ....................................

1917745

Hardened Washer...................................

1917579

V-Belt .....................................................

1918246

Spindle Head Adapter (Incl. Bearing) .....

1917581

Spindle Shaft..........................................

1918329

Spindle Head Assembly (Incl. Bearing,

Insert, and Refs. 16, 17, 18)...............

1918393

Trimmer Head Assembly (Incl. Ref. 27) .

1915220001

Wear Cup ...............................................

1917599

Square Washer.......................................

1724491

Self-Tap Screw, 5/16-18 x 3/4................

1917573

Cable Bracket .........................................

1910849

Idler Spring ............................................

1917746

Flat Washer ............................................

1917589

Control Cable - Trimmer Head ...............

1910857

Button Hd. Screw, 3/8-16 x 1-1/2...........

1917572

Idler Arm ................................................

1910855

Idler Pulley .............................................

1186393

Flange Lock Nut, 3/8-16 .........................

1918332

Rubber Shim Kit (2 shims per kit)..........

Ref. # Part # Description Qty.

PARTS LIST – DRAWING NO. 2

Summary of Contents for 52063, 52064

























Search results

Summary of Contents for 52063, 52064

Reviews:

Related manuals for 52063, 52064

Brands by name

Popular brands

Troy-Bilt 52063, 52064, Owner'S Manual

Search results

Summary of Contents for 52063, 52064

Reviews:

Related manuals for 52063, 52064

Brands by name

Popular brands