background image

Features and Controls

3

Section

7

OPERATING SYMBOLS

Various symbols (shown here, with
word descriptions) are used on the
unit.

STOP

FEATURES AND CONTROLS

This Section describes the location and
function of the features and controls on
your machine.  Refer to the following
Operation Section for detailed operating
instructions.

IMPORTANT: Refer to the engine manual
for detailed information about the con-
trols on the engine.

Trimmer Head Control Bail 

Pull the control bail (A, Figure 3-1) up
against the handlebar (engage bail) to
start rotation of the trimmer head.  Let go
of the control bail (disengage bail) to
stop the trimmer head. 

Cutting Height Settings

The trimmer head (B, Figure 3-1) is
adjustable to an infinite number of height
settings from 1-1/2" -to- 4-1/2".

Trimmer Line Holders

The trimmer lines are secured to line
holders (C, Figure 3-1).  Replacing the
trimmer lines is a simple procedure (see
“Changing Trimming Lines” in Section
5). 

Handlebar Height Adjustment

The handlebar (D, Figure 3-1) has two
height settings (see “Adjust Handlebar
Height” in Section 4).

Plastic Debris Shield

The plastic debris shield (E, Figure 3-1)
protects the engine from all manner of
debris.  The shield tilts forward for
access to the engine.

Engine Throttle Control Lever

Use this lever (F, Figure 3-1) to regulate
engine speed and to stop the engine. The
throttle settings are shown on the decal
next to the lever.

Engine Recoil Starter

The recoil starter (G, Figure 3-1) is
located at the rear of the engine and is
used to pull start the engine.

Fuel Primer Button

The fuel primer button (I, Figure 3-2)
allows a cold engine to be primed for
faster, easier starting.  

Keyswitch

The keyswitch (J, Figure 3-1) activates
the starter motor to start the engine.  The
keyswitch does not have an engine stop
position.  Use the Engine Throttle Control
Lever (F) to stop the engine.  

IMPORTANT: Remove key from
keyswitch when leaving unit unattended
to help prevent unauthorized or uninten-
tional starting.

Battery

The battery (K, Figure 3-1) cranks the
engine starter motor when the keyswitch
is turned to the start position.  Do not
crank engine longer than five (5) seconds
per each starting attempt.

ENGINE

STOP

TRIMMER

HEAD

ENGAGE

BAIL

DISENGAGE

BAIL

SLOW

FAST

STOP

Figure 3-1:  Features and controls (electric start model shown).

J

C

B

G

K

F

A

E

I

D

Before operating your machine, care-
fully read and understand all safety,
controls  and operating instructions in
this Manual, the separate Engine
Owner’s Manual, and on the decals on
the machine.

Failure to follow these instructions can
result in serious personal injury.

WARNING

Summary of Contents for 52063, 52064

























Reviews: