background image

1905693 (5/01)

Printed in U.S.A.

©

2001 Garden Way Incorporated

CUSTOMER SERVICE INFORMATION

Owner Registration Card

Please fill out and mail the enclosed owner
registration card.  The purpose of this card is
to register each unit at the factory so that we
can provide you with warranty benefits and
informational bulletins.

Warranty Service

The warranty statement is included in the unit’s literature
package.

Model/Serial Numbers

A Model/Serial Numbers decal is located on the side of the
deck.  For ready reference, record these numbers in the
spaces below.

Date of Purchase: 

Model Number:

Serial Number:

Authorized Dealer Information

If you purchased your unit from an authorized dealer, record
the dealer’s address and phone number below for ready refer-
ence:

Dealer Name: 

Address:

Phone:

IMPORTANT:

Left and right sides of the unit are determined by standing

behind the unit, in the operator’s position, and facing in the

direction of forward travel.

NOTICE:

We reserve the right to change specifications, add

improvements or discontinue the manufacture of any of our

equipment without notice or obligation to purchasers of our

equipment.

M

I

A

L

M

I

A

L

Customer Service and Technical Service

If you have questions or problems with the
unit, contact your local dealer or the factory.
(When calling or writing, provide the
Model/Serial Numbers of the unit.)

Replacement Parts

Factory specified replacement parts are
available from your authorized dealer or
directly from the factory.  When ordering
parts, be sure to provide the following:

• Model/Serial Numbers of the unit.

• Part number of the part needed.

• Part Description.

• Quantity needed.

NOTE: All replacement parts must conform to our rigid quality
specifications. Although some replacement parts we provide
may vary slightly in shape, color or texture from the original
parts, any variations will not affect the fit or performance of
these parts on your unit.

Engine Service and Repair

For engine service or repair, contact your
nearest authorized engine dealer (look in the
Yellow Pages under “Engines–Gasoline”).
The engine is warranted by the engine man-
ufacturer. Any unauthorized work performed
on the engine during the warranty period
may void this warranty.  For complete
details on the engine warranty, refer to the
Engine Owner’s Manual.

For customer assistance, contact your nearest authorized dealer or:

GARDEN WAY INCORPORATED  •

1 Garden Way  •  Troy, New York 12180

Customer Service: 1-800-437-8686  •  Technical Service: 1-800-520-5520  •  Parts Service: 1-800-648-6776 

•  FAX: (518) 233-4622  •  WEBSITE: www.troybilt.com

Outside the United States and Canada:

Customer Service: (518) 233-4807  •  Technical Service: (518) 233-4808  •  Parts Service: (518) 233-4806  •  FAX (518) 233-4622

We urge using only genuine replacement parts, which
meet all the latest requirements. Replacement parts
manufactured by others could present safety hazards,
even though they may fit on the unit.

WARNING

Summary of Contents for 52063, 52064

























Reviews: