background image

                                                                                            -        -                                                                XM464-V1.2-NR 

 

fixture individually. 
If you set the same address, all the units will start to “listen” to the same control signal from the same channel 
number. In other words, changing the settings of one channel will affect all the fixtures simultaneously. 
If you set a different address, each unit will start to “listen” to the channel number you have set, based on the 
quantity of control channels of the unit. That means changing the settings of one channel will affect only the 
selected fixture. 
 
In the case of the move head, which is a 14 channel fixture, you should set the starting address of the first unit 
to 1, the second unit to 15 (14 + 1), the third to 29 (14 + 15), and so on. 

 

Note:

 

The modes of DMX 512 data are shown via the display: 

DMX OK

NO DMX

 

1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the data 
is  received,  the  display  will  show 

"A.001"

  with  the  actually  set  address.  If  there  is  no  data  received  at  the 

DMX-input, the display will flash 

"A001"

 with the actually set address. 

This situation can occur if: 
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device. 
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are swap in 
the input connector. 
 
It’s necessary  to  insert  the  XLR  termination  plug  (with  120  Ohm)  in  the  last  lighting  in  the  link  in  order  to 
ensure proper transmission on the DMX data link. 
 

 
Control Board 

There are four keys on the control panel , which could be used to set the address, turn ON/OFF, operating the 
program and reset. 
  

[Mode/Esc]

 press this key to enter into edit mode. Press this key under the edit mode if you want to return to 

previous menu. it will exit from edit mode 60 seconds after the last keypress 
  

[UP]

 screen will flash when pressing this key in normal mode, the adress value will increasing. Keep pressing 

this key, the address value will increase rapidly. it will exit from flash 60 seconds after the last keypress. Press 
this key under edit mode, you can choose the function you want from the buttom up in the menu. 
  

[DOWN] 

screen will flash when pressing this key in normal mode, the adress value will idecreasing. Keep 

pressing this key, the address value will decrease rapidly. it will exit from flash 60 seconds after the last 
keypress. Press this key under edit mode, you can choose the function you want from the top down in the menu. 
  

[ENTER] 

this key is functionless when in normal mode. Press this key under the edit mode, it will enter into 

next menu. 

 

 
 
 
 
 

 

 

 

 

 

 

Summary of Contents for WALLY MH 50























Reviews: