background image

                                                                                            -        -                                                                XM464-V1.2-NR 

16

 

INSTRUCTIONS ON USE: 

DMX channel´s functions and their values (14 DMX channels): 

Mode/Channel 

Value 

Function 

St 

Ba 

Ex 

 

 

 

 

 

 

Color Wheel 

0-14 

Open / white 

15-29 

Color1 

30-44 

Color2 

45-59 

Color3 

60-74 

Color4 

75-89 

Color5 

90-104 

Color6 

105-119 

Color7 

120-127 

Color8 

128-189 

Forwards rainbow effect from fast to slow 

190-193 

No rotation 

194-255 

Backwards rainbow effect from slow to fast 

 

 

 

 

Rotating gobos, cont. rotation 

0-9 

Open 

10-19 

Rot. gobo 1   

20-29 

Rot. gobo 2 

30-39 

Rot. gobo 3 

40-49 

Rot. gobo 4 

50-59 

Rot. gobo 5 

60-69 

Rot. gobo 6 

70-79 

Rot. gobo 7 

80-95 

Rot. gobo 1    shake 

96-111 

Rot. gobo 2    shake 

112-127 

Rot. gobo 3    shake 

128-143 

Rot. gobo 4    shake 

144-159 

Rot. gobo 5    shake 

160-175 

Rot. gobo 6    shake 

176-191 

Rot. gobo 7    shake 

192-255 

Rot. gobo wheel cont. rotation slow to fast   

 

 

 

 

Rotating gobo index, rotating gobo rotation 

0-127 

Gobo indexing 

128-189 

Forwards gobo rotation from fast to slow 

190-193 

No rotation 

194-255 

Backwards gobo rotation from slow to fast 

 

 

 

 

Speed pan/tilt movement 

0-225 

Max to min speed 

226-235 

Blackout by movement 

236-245 

Blackout by all wheel changing 

246-255 

No function 

Summary of Contents for WALLY MH 50























Reviews: