background image

4

1

2

3

4

5

6

7

Individual models may vary slightly from diagram.

2.2 Battery Access Panel (Cover Removed)

2. Control Panels 

(continued)

Internal Battery Packs: 

1. 

These supply backup runtime to connected equipment. Each pack consists of two strings (one positive and one negative). 

The number of included battery packs varies depending on UPS model number. Battery packs must replaced by a qualified electrician. 

Note: The 

UPS system ships with the internal batteries disconnected. Refer to the 

Adding or Replacing Internal Batteries

 section for battery connection 

instructions.
Battery Cartridge Fuses: 

2. 

Protect against short circuit damage. If a heavy overload or short circuit is encountered, a fuse will blow. A battery pack 

with a blown fuse will not deliver any output voltage to the UPS system. The fuses must be replaced by a qualified electrician. (See section 7, 

Adding or Replacing Internal Batteries

 for details.)

Internal Battery Pack Connectors (Red & Black):

3. 

 Connect the individual internal battery packs to the overall battery system.

Internal Battery Pack Jumper Cables (White & Blue):

4. 

 Connect the internal battery pack strings together through the fuse block.

Battery System Connectors: 

5. 

One connector (internal, not shown) connects the battery module to the power module. The other connector (shown) 

connects the battery module to an additional optional battery module (not shown, available separately from Tripp Lite). The battery system 
connectors are only utilized when adding an additional battery module. Use of these connectors is outlined in the owner's manual included with the 
additional battery module.

Extended Runtime Capability:

6. 

 Open slots accept additional internal battery packs (available separately from Tripp Lite) to extend runtime. The 

number of open slots varies depending on UPS model number. All models accept the connection of an additional battery module (available 
separately from Tripp Lite) to further extend runtime. Contact Tripp Lite for details.

Fuse Block Bracket:

7. 

 Accepts battery cartridge fuses.

Summary of Contents for SmartOnline 120/208V



















Reviews: