manualshive.com logo in svg

Traxon Allegro Dot M/L Diffused View, Installation Manual, Page: 3 / 23

Share
Download
Traxon Allegro Dot M/L Diffused View Installation Manual Download Page 3

www.traxontechnologies.com

©2019 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. 
PATENTS, JAPAN PATENTS, OTHER PATENTS PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide

12/19 V2.0

3 of 23

SAFETY AND OPERATION

1.  CAUTION - Unplug the power supply from the mains power before connecting any 

cables as this can damage the products.

2.  CAUTION - Avoid looking directly into the LED light source at close range for your own 

safety.

3.  Persons installing this product should make sure:

a. The installation complies with all applicable codes, state and local laws, 

ordinances, standards and safety regulations.

b. The installation environment is carefully studied and suitable surge protection 

measure(s) is taken.

c. He or she is qualified for the handling of electrical equipment.

4.  Do not attempt to install or use the product until installation instructions and safety labels 

are fully understood. This product is designed for indoor and outdoor use.

5.  Ensure product operates within the specified temperature range. (Refer to 5. TECHNICAL 

SPECIFICATION for more details.)

6.  Do not attempt to open the product. Not user serviceable.
7.  Do not use the product if any part of it, or the power cables are damaged.
8.  Only use product for specified voltage, do not exceed. (Refer to 5. TECHNICAL 

SPECIFICATION for more details.)

9.  Always maintain connection to ensure waterproofing.
10.  If the product has been subjected to drastic temperature variances, for example, 

following transportation, do not connect the fixture until it has reached room temperature, 
as moisture condensation may cause electric shock and product damages.

11.  When installing the products and system power supplies, please ensure they will not 

be exposed to moisture and extreme heat (and direct sunlight for outdoor products). 
Besides, keep a clean operating environment for the fixtures and system power supplies.

12.  Please study this Installation Guide thoroughly and check the latest Technical 

Specification Sheets available from the Traxon website www.traxontechnologies.com 
before setup.

13.  Any non-compliance of the Installation Guide will void the Traxon warranty.

Please read through Safety and Operation before start of the installation.

Summary of Contents for Allegro Dot M/L Diffused View
























Reviews:

No comments