Travis Industries Xtreme 6020 Installation Manual Download Page 2

Page: 2 / 50

2 Introduction

4140717

100-01351

Overview

This manual details the installation requirements for
the Xtreme 6020 fireplace. For operating and
maintenance instructions, refer to the Owner's
Manual (part # 100-01247).

Listing Details

This appliance was listed by Intertek (Warnock
Hersey) to ANSI Z21.50b-2009 / CSA 2.22b-2009 -
report # 3183426 The listing label is chained to the
appliance near the glass frame. A copy is shown to
the right.

IAS (ICBO) Approval

This appliance was listed by Intertek (Warnock
Hersey) - IAS # TL271.

Massachusetts Approval

This manual has been submitted to the
Massachusetts Board of State Examiners of
Plumbers and Gas Fitters

National Fireplace Institute

Report No. 100866534PRT

-001

Control No. 4000515

nted Gas Fireplace Heater

Xtreme 6020 L.P

Xtreme 6020 N.G.

Tested to:

ANSI Z21.50b-2009/CSA

2.22b-2009 “V

ented Gas Fireplace”

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas

Code,

ANSI Z223.1/NFP

54, or Natural Gas and Propane Installation Codes, CSA

B149.1.

This vented gas fireplace heater is equipped at the factory for use with gas fuel marked above. No conversion is

allowed.

This vented gas fireplace heater is not for use with air filters.

Keep burner and control compartment clean. See installation and operating instructions accompanying

appliance.

This appliance must be properly connected to a venting system in accordance with the manufacturer

’s

installation instructions. See owner

’s

manual for approved brands of venting.

ARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property

damage. Refer to the owner

’s

information manual provided with this appliance. For assistance or additional

information consult a qualified installer

, service agency or the gas supplier

VENTED GAS FIREPLACE HEA

ER - NOT FOR USE WITH SOLID FUEL

Minimum Clearances to Combustibles

Fireplace to

Adjacent W

all

od Floor Beneath Fireplace

Back to Enclosure

3” (76mm)

0” (0mm)

p to Enclosure

Sides to Enclosure

Base of Fireplace to a Mantel

37.5” (953mm)

3” (76mm)

See Owner

’s

Manual

Minimum Inlet Pressure (inches W

.C.)

Maximum Inlet Pressure (inches W

.C.)

Manifold Pressure on “HI” (inches W

.C.)

L.P

”

13”

”

N.G.

5.5”

7”

3.5”

Input Rate on “HI” (BTU/Hr)

Input Rate on “LO” (BTU/Hr)

Orifice Size - Center (DMS)

Orifice Size - Sides (DMS)

L.P

90,000

45,649

#46

#54

N.G.

90,000

57,896

#25

#46

This appliance is equipped for use only at altitudes 0-2,000 feet (0-610m) in the USA. In Canada, 0-4,500 feet (0-1370m).

For altitudes above 2,000 feet, the vent configuration, orifice, or combination of both may need to be changed.

See owner

’s

manual for information on making these changes.

2014

2015

2013

Feb.

Mar

Jan.

May

Jun.

Apr

Aug.

Sep.

Jul.

Nov

Dec.

Oct.

MANUF

ACTURE DA

TE:

ARNING: Failure to install this appliance per the manufacturer

’s

instructions or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury

4800 Harbour Pointe Blvd. SW

Mukilteo, W

98275

Manufactured by:

www

.travisproducts.com

CAUTION:

Do not operate this appliance with glass removed, cracked or broken. Replacement of the panel(s) should be done

by a licensed or qualified service person.

0867

Summary of Contents for Xtreme 6020



















































Search results

Summary of Contents for Xtreme 6020

Reviews:

Brands by name

Popular brands

Travis Industries Xtreme 6020, Installation Manual

Search results

Summary of Contents for Xtreme 6020

Reviews:

Brands by name

Popular brands