2/8
6-1620026 rev.P4 22/02/2016
5
4
While the receiver is in standby the display shows the selected mode of functioning (
mode1
,
mode2
,
mode3
,
mode4
,
mode5
,
mode6
). During the process
of a timed command, the display blinks. During a step by step command, as in mode 5 and 6, the display does not blink.
To enter the menu, press briefly the P3 button.
Press briefly the P3 button to move inside the items of the menu and use the POTENTIOMETER
to change the parameters.
The receiver saves the parameters when it quits the menu.
MENU
DESCRIPTION
SELECTABLE
VALUES
min-max
DEFAULT
UNIT
fUNCT
FUNCTION
Menu for the selection of the functioning mode:
1
- Dual independent outputs.
2
- Switching network.
3
- Vestibule sequencing, type 1.
4
- Vestibule sequencing, type 2.
5
- Latched mode 1.
6
- Latched mode 2.
1 - 6
1
-
Ton1
ACTIVATION TIME FOR RELAY 1
1 - 60
1
s
Ton2
ACTIVATION TIME FOR RELAY 2
1 - 60
1
s
TdLy
DELAY TIME BETWEEN THE ACTIVATION OF THE TWO RELAYS
1 - 60
1
s
Power
POWER OF THE SIGNAL
The display shows the quality of the transmission signal.
BAD - BEST
-
-
5.1 - FUNCTION
By accessing the item
funct
it is possible to set the functioning mode:
1
- Dual independent outputs: operates as a two channels receiver.
2
- Switching network: also known as a switching network or make/break relay, use this mode with a door operator & lock.
3
- Vestibule sequencing, type 1: to be selected if you want to sequence two doors in both directions, using just one receiver (requires two
conductors to the second door).
4
- Vestibule sequencing, type 2: to be selected if you want to sequence two doors in both directions, using two receivers and no wiring between operators.
5
- Latched mode 1: access control application. A transmitter signal programmed into the channel 1 will latch relay 1. While the relay 1 is latched, a
transmitter programmed into the channel 2 will activate the relay 2. When the channel 1 is in the off state, the receiver will ignore the channel 2 inputs.
6
- Latched mode 2: freight door application. In this mode a transmitter will active the relay 1 for an adjustable time, then latch the relay 2. The
relay 2 stays latched until another transmitter signal is received, then drops out immediately.
5.2 - ACTIVATION TIME FOR RELAY 1
By accessing the item
ton1
it is possible to select the activation time of the relay 1. Use the
POTENTIOMETER
to set a value between 1 and 60 s.
5.3 - ACTIVATION TIME FOR RELAY 2
By accessing the item
ton2
it is possible to select the activation time of the relay 2. Use the
POTENTIOMETER
to set a value between 1 and 60 s.
5.4 - DELAY TIME BETWEEN THE ACTIVATION OF THE TWO RELAYS
By accessing the item
tdLY
it is possible to select the delay time between the activation of the two relays. Use the
POTENTIOMETER
to set a value
between 1 and 60 s.
5.5 - POWER OF THE SIGNAL
By accessing the item
power
it is possible to verify the quality of the transmission signal of a transmitter already memorized.
When the display shows
-----
, press the button of the transmitter. The display can show:
•
bad
: the signal quality is very low.
With a low signal quality it is suggested that you move the receiver to improve the signal.
•
g
ood
: the signal quality is good.
•
best
: the signal quality is very high.
MENU
It is possible to select the code type in use on the receiver.
Follow this procedure for the selection:
1. Switch off the power supply.
2. Press and hold at the same moment all the buttons of the receiver. After 5 seconds, OUT1 and OUT2 leds blink:
•
3 times if the Rolling Code is enable. The display shows
BiroL
.
•
6 times if the Sawn Rolling Code is enable (Transmitter Solutions 433 MHz + KEELOQ
®
HCS300-301 compatible). The display shows
sawn
.
When the Sawn Rolling Code is set, a point appears on the display between the 3rd and the 4th digit.
CODE TYPE SELECTION
1. Press and hold the P2 button.
2. When the display shows
C2CLr
and the OUT2 led blinks fast for 3s, release the button. The transmitters have been deleted from the relay 2.
To delete a single trasmitter from the memory, follow the following steps:
1. Press the P1 or P2 button. The display shows
rad1
or
rad2
.
2. Press the 1st key and the hidden button at the same moment of the transmitter that you want to erase.
3. When the display shows
CLEAR
, release the buttons. The transmitter has been deleted from the memory.
