Transition Networks SISTP10xx-141-LR Installation Manual Download Page 8 | Manualshive

Page: 8 / 42

background image

Transition Networks

SISTP10xx-141-LR(T) Industrial PoE Switch

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

vi

Cautions and warnings, continued

Warnings

Warnings indicate the possibility of injury to persons.

WARNING

Be sure to disconnect power before installing and wiring the Industrial PoE Switch.
Failure to observe this warning could result in an electrical shock.

WARNING

Fiber optics: Visible and invisible laser radiation when open: DO NOT stare into the
beam, or directly view the beam with optical instruments. Failure to observe this warning
could result in an eye injury or blindness.

WARNING

Use of controls, adjustments or the performance of procedures other than those
specified herein may result in hazardous radiation exposure.

«
...
6
7
8
9
10
...
»

Summary of Contents for SISTP10xx-141-LR











































Reviews:

No comments

Related manuals for SISTP10xx-141-LR

Brand: IBM Pages: 44

Brand: PRO SIGNAL Pages: 5

Brand: DAB Pages: 56

Brand: Cabletron Systems Pages: 120

PC-IA100 Series

Brand: Barox Pages: 7

Brand: ALFAtron Pages: 68

Brand: 3onedata Pages: 2

Brand: Comm-Tec Pages: 48

Brand: Lightwave Pages: 53

Brand: Stahl Pages: 29

CheetaHub Classic-2041

Brand: Accton Technology Pages: 7

Brand: Eaton Pages: 3

Brand: CTC Union Pages: 14

EXT-DVIK-MV-441

Brand: Gefen Pages: 136

Brand: Edge-Core Pages: 2

Brand: Clear-Com Pages: 21

Brand: EGig Pages: 10

Brand: Niveo Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands