Transition Networks SISTP10xx-141-LR Installation Manual Download Page 10 | Manualshive

Page: 10 / 42

background image

Transition Networks

SISTP10xx-141-LR(T) Industrial PoE Switch

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

2

General description

Overview

The SISTP10xx-141 unmanaged Industrial PoE Switch can help eliminate EMI or RFI issues
and help to overcome distance limitations with copper-based cabling by providing a fiber
interface to transport data from copper-based industrial networking and communication
devices over fiber optic cabling. In addition, these PoE switches are industrial hardened
Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that
comply with the IEEE802.3af

TM

Power over Ethernet standard.

Each Industrial PoE Switch can connect to either 10Base-T or 100Base-TX copper ports and
provides a 100Base-FX fiber optic connection.  In addition, the four RJ-45 ports also provide
power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair
cabling.  Multiple fiber optic connector options are offered as well as two distinct operating
temperature ranges:

-

Standard: -10°C to +50°C (14°F to +122°F)

-

Extended: -40°C to +65°C (-40°F to +149°F)

Features

The SISTP10xx-141 Industrial PoE Switch has the following features:

•

Auto-Negotiation

•

AutoCross

TM

•

IEEE802.3af Power over Ethernet compliant

•

4-port integrated POE injector with full 15.4 Watts per port on data pairs

•

Under-current detection and over current protection [re-settable fuse]

•

Dual, redundant auto-sensing 48VDC inputs with reverse polarity protection

•

Dry Contact Relay alarm output for failure of primary or redundant power input

•

IEEE 802.3x flow control support

Flow control on full-duplex

Back pressure on half-duplex

•

1K MAC address table

•

Full wire-speed with 1Gbps backplane switching fabric

•

DIN-Rail mounting bracket (installed)

•

Wall mount brackets included

•

IP30 protection metal enclosure

•

Lifetime Warranty

«
...
8
9
10
11
12
...
»

Summary of Contents for SISTP10xx-141-LR











































Reviews:

No comments

Related manuals for SISTP10xx-141-LR

Brand: CALIENT Pages: 22

Brand: JB Systems Light Pages: 15

Brand: Zigen Pages: 40

Brand: Zigen Pages: 4

Brand: Adler Pages: 8

PowerSwitch Z9332F-ON

Brand: Dell EMC Pages: 16

Brand: Audio Authority Pages: 12

EX ZS 92 S 22 VD F

Brand: steute Pages: 28

Brand: Black Box Pages: 4

CN8000 KVM on the NET

Brand: ATEN Pages: 2

Brand: Festo Pages: 2

Brand: Eaton Pages: 5

Brand: Samson Pages: 64

Brand: KanexPro Pages: 35

Brand: C&C TECHNIC Pages: 2

Brand: KinAn Pages: 5

Hi-Speed USB 4-Port Bay Hub

Brand: SIIG Pages: 8

Brand: H3C Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands