Transition Networks MIL-SEM24T4GPA User Manual Download Page 12

Page: 12 / 59

Green

The port is successfully connecting

with the device.

Blinks

The port is receiving or transmitting

data.

Off

No device attached.

Blinks

Collision packet detection

LNK / ACT

(SFP)

Off

No device attached.

Rear Panel

The 3-pronged power plug is located at the Rear Panel of the MIL-SEM24T4GPA

Switch as shown in figure. The Switches will work with AC in the range 100-240V

AC, 50-60Hz.

Rear Panel of the

MIL-SEM24T4GPA

Switch

Desktop Installation

Set the switch on a sufficiently large flat space with a power outlet nearby. The

surface where you put your Switch should be clean, smooth, level, and sturdy.

Make sure there is enough clearance around the Switch to allow attachment of

cables, power cord and air circulation.

Attaching Rubber Feet

Summary of Contents for MIL-SEM24T4GPA




























































Search results

Summary of Contents for MIL-SEM24T4GPA

Reviews:

Related manuals for MIL-SEM24T4GPA

Brands by name

Popular brands

Transition Networks MIL-SEM24T4GPA, User Manual

Search results

Summary of Contents for MIL-SEM24T4GPA

Reviews:

Related manuals for MIL-SEM24T4GPA

Brands by name

Popular brands