background image

XT500C DELUXE PROGRAMMABLE HEAT-PUMP THERMOSTAT

9

69-1404

Pub. No. 18-HD25D2-2

Fig. 15 . Display of test number.

Refer to Table 5 for the directions and results of the specific tests.

Fig. 14. Display of all the segments of the LCD.

Table  4. Tests Available In The Installer Self-Test.

NOTE:

Press Time 

 to advance to the next test and Time 

 to go back to the previous test. Press Run Program to exit the

self-test. This mode times out 5 minutes after the last key press.

Table 5. Installer Self-Test Options.

(

continued)

Test  
Number

Self-Test Description

10

Heating  Equipment

20

Emergency  Heat  Equipment  (HP  systems
only)

30

Cooling Equipment

40

Fan  Equipment

50

Comfort-R  Terminals  (H-H)

60

Keyboard Operation

70

Device  Information

M14559

Aux Ht

Set Day/Time

Set Program

Mon
Wake Leave Return

Sleep

Outdoor

Room

Filter

Wait

System

Fan

Em Heat

On

Auto

Off

Cool

Auto

AM

PM

Hold for

Heat Cool

Repl Batt

Recovery

DST

Tue Wed Thu Fri Sat Sun

Days

Temporary Setting

Em Ht

M14612

Key to
Press

Test
Number

Description

Heating Equipment Self-Test (10)

Time 

10

Enter heating equipment self-test.   

Temp

 ▲

11

First stage heat turns on.

Temp

 ▲

12

Second stage heat (some models) turns on.

Temp

 ▲

13

Third stage heat (some models) turns on.

Temp

 ▼

12

Third stage heat (some models) turns off.

Temp

 ▼

11

Second stage heat (some models) turns off.

Temp

 ▼

10

First stage heat turns off.

Emergency Heat Equipment Self-Test (20)

Time 

20

Enter emergency heating equipment self-test.

Temp

 

21

Emergency heat turns on.

Temp

 ▼

20

Emergency heat turns off.

Cooling Equipment Self-Test (30)

Time 

30

Enter cooling equipment self-test.   

Temp

 ▲

31

First stage cool and fan turn on.

Temp

 ▲

32

Second stage cool (some models) turns on.

Temp

 ▲

31

Second stage cool (some models) turns off.

Temp

 ▼

30

First stage cool and fan turn off.

Fan Equipment Self-Test (40)

Time 

40

Enter fan equipment self-test.

Temp

 ▲

41

Fan turns on.

Temp

 ▼

40

Fan turns off.

Summary of Contents for XT500C













Reviews: