Tractive Technology AUTO-BLiP User Manual Download

Page: 4 / 12

Page 4

INSTALLATION INSTRUCTIONS

Signal
Description

AUTO-BLiP
harness color
wire below,
connects to….

…. Viper harness
color coded wire

Viper wire
in harness
plug

Location of
harness plug

Accelerator
Pedal Position
Sensor1

Red (or Green)

BROWN/white

Under Dash

- Black

oval plug to upper
left above pedal.

Accelerator
Pedal Position
Sensor2

Green (or Red)

WHITE/brown

Under Dash

- Black

oval plug to upper
left above pedal.

Brake Activation
Sensor

Blue

LT BLUE/green

Under Dash

- Light

gray flat plug above
brake pedal facing
in-upwards on
switch/plunger
assembly.

12-Volt constant
on source
Positive (+)

White

RED

Under Dash

- Light

gray flat plug above
brake pedal facing
in-upwards on
switch/plunger
assembly.

Clutch Activation
Interlock Switch

Yellow

YELLOW/orange

#2 - middle

Engine Bay

–

Directly below ECU
harness exit from
firewall.

Negative (-)

Black

BLACK

Under Dash

- Light

gray flat plug above
brake pedal facing
in-upwards on
switch/plunger
assembly.

Summary of Contents for AUTO-BLiP












Search results

Summary of Contents for AUTO-BLiP

Reviews:

Related manuals for AUTO-BLiP

Brands by name

Popular brands

Tractive Technology AUTO-BLiP, User Manual

Search results

Summary of Contents for AUTO-BLiP

Reviews:

Related manuals for AUTO-BLiP

Brands by name

Popular brands