TP-Link TL-R480T User Manual Download Page 24

Page: 24 / 60

TL-R480T

Enterprise Broadband Router User Giude

2) If you click the

Save

button, the router will prompt you to reboot.

5.4.4 Bandwidth Control

You can control bandwidth of each LAN port on this page. This feature can be used for
distributing flexibly Internet resource.

Figure 5-9 Bandwidth Control

LAN

- LAN port number.

LAN1

point to LAN port 1,

LAN2

point to LAN port 2, and

so on.

Bandwidth

- Select the bandwidth value from 128Kbps, 256Kbps, 512Kbps,

1Mbps, 2Mbps, 4Mbps and 8Mbps. The selected value is the maximum Internet
bandwidth for the LAN port.

No-limit

means no bandwidth limit.

5.4.5 VLAN

On this page, you can configure

VLAN

based on LAN port. There are three VLAN

modes in the

VLAN Mode

pull-down list:

One VLAN

Two VLAN

and

Four VLAN

, the

default is

One VLAN

Figure 5-10 VLAN Settings

One VLAN

- In this VLAN mode, all LAN ports are in one VLAN, all LAN ports can

communicate with each other.

Two VLANs

- In this VLAN mode, the LAN1 and LAN2 are in one VLAN, and the

LAN3 and LAN4 are in another VLAN. So LAN1 can communicate with LAN2 and
LAN3 can communicate with LAN4, but LAN1 or LAN2 cannot communicate with
LAN3 or LAN4.

Four VLANs

- In this VLAN mode, all ports are in different VLANs. So they cannot

communicate with each other.

5.4.6 Port Mirror

You can configure LAN port mirror feature on this page.

- 20 -

Summary of Contents for TL-R480T





























































Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands

TP-Link TL-R480T, User Manual

Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands