TP-Link TL-R480T User Manual Download Page 40

Page: 40 / 60

TL-R480T

Enterprise Broadband Router User Giude

Figure 5-30 Advanced Security settings

Packets Statistic interval (5 ~ 60)

The default value is 10. Select a value

between 5 and 60 seconds in the pull-down list. The

Packets Statistic interval

value indicates the time section of the packets statistic. The result of the statistic
used for analysis by

SYN Flood

UDP Flood

and

ICMP-Flood

DoS protection

Enable

Disable

the DoS protection function. Only when it is

enabled, will the flood filters be effective.

Enable ICMP-FLOOD Attack Filtering

Enable

Disable

the

ICMP-FLOOD

Attack Filtering.

ICMP-FLOOD Packets threshold: (5 ~ 3600)

The default value is 50. Enter a

value between 5 ~ 3600 packets. When the current

ICMP-FLOOD

Packets

numbers are beyond the set value, the router will start up the blocking function
immediately.

Enable UDP-FLOOD Filtering

Enable

Disable

the

UDP-FLOOD

Filtering.

UDP-FLOOD Packets threshold: (5 ~ 3600)

The default value is 50. Enter a

value between 5 ~ 3600 packets. When the current

UPD-FLOOD

Packets numbers

are beyond the set value, the router will start up the blocking function immediately.

Enable TCP-SYN-FLOOD Attack Filtering

Enable

Disable

the

TCP-SYN-

FLOOD

Attack Filtering.

TCP-SYN-FLOOD Packets threshold: (5 ~ 3600)

The default value is 50. Enter

a value between 5 ~ 3600 packets. When the current

TCP-SYN-FLOOD

Packets

numbers is beyond the set value, the router will start up the blocking function
immediately.

Ignore Ping Packet from WAN Port

Enable

Disable

ignore ping packet from

- 36 -

Summary of Contents for TL-R480T





























































Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands

TP-Link TL-R480T, User Manual

Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands