TP-Link TL-R480T User Manual Download Page 46

Page: 46 / 60

TL-R480T

Enterprise Broadband Router User Giude

the router is not experiencing difficulties, there is no need to download a more recent
firmware version, unless the version has a new feature that you want to use.

Note: When you upgrade the router's firmware, you may lose its configuration

settings, so make sure you write down the router settings before you upgrade its

firmware.

To upgrade the router's firmware, follow these instructions:
1. Download a more recent firmware upgrade file from the TP-LINK website

(

www.tp-link.com

2. Run a TFTP Server on a PC on your LAN, and take the file in the TFTP server’s

path.

3. Type the downloaded file name into the

File Name

box.

4. Type the IP address of the PC that runs the TFTP server in the

TFTP Server’s IP

Address

field.

5. Click

the

Upgrade

button.

Firmware Version

displays the current firmware version.

Hardware Version

displays the current hardware version. The hardware version

of the upgrade file must accord with the current hardware version.

Note:

Do not turn off the router or press the Reset button while the firmware is

being upgraded.

2. The router will reboot after the upgrading has been finished.

5.10.3 Factory Defaults

This page (shown in figure 5-38) allows you to restore the factory default settings for the
router.

Figure 5-38 Restore Factory Default

Click the

Restore

button to reset all configuration settings to their default values.

•

The default

User Name

: admin

•

The default

Password

: admin

•

The default

IP Address

: 192.168.1.1

•

The default

Subnet Mask

: 255.255.255.0

Note

: Any settings you have saved will be lost when the default settings are restored.

5.10.4 Reboot

This page (shown in figure 5-39) allows you to reboot the router.

- 42 -

Summary of Contents for TL-R480T





























































Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands

TP-Link TL-R480T, User Manual

Search results

Summary of Contents for TL-R480T

Reviews:

Related manuals for TL-R480T

Brands by name

Popular brands