TP-Link TD-W8151N User Manual Download Page 12

Page: 12 / 87

TD-W8151N

150Mbps Wireless N ADSL2+ Modem Router User Guide

Chapter 2 Hardware Installation

2.1 The Front Panel

Figure 2-1

The LEDs located on the front panel indicates the device’s working status. For details, please refer
to LED Explanation.

LED Explanation:

Name

Status Indication

The modem router is powered on.

(Power)

Off

The modem router is off. Please ensure that the power adapter is
connected correctly.

ADSL line is synchronized and ready to use.

Flash

The ADSL negotiation is in progress.

(ADSL)

Off

ADSL synchronization fails. Please refer to

Note 1

for

troubleshooting.

The network is available with a successful Internet connection.

Flash

There is data being transmitted or received via the Internet.

(Internet)

Off

There is no successful Internet connection or the modem router is
operating in Bridge mode. Please refer to

Note 2

for troubleshooting.

Wireless is enabled but no data is being transmitted.

Flash

The modem router is sending or receiving data over the wireless
network.

(WLAN)

Off

Wireless function is disabled.

A wireless device has been successfully added to the network by
WPS function.

Flash

WPS handshaking is in process and will continue for about 2
minutes. Please press the WPS button on other wireless devices
that you want to add to the network while the LED is flashing.

(WPS)

Off

The WPS function is disabled or the wireless device fails to be added
to the network in 2 minutes after WPS function is enabled. Please
refer to

4.3.3.1 WPS Settings

for more information.

There is a device connected to this LAN port.

Flash

The modem router is sending or receiving data over this LAN port.

(LAN)

Off

There is no device connected to this LAN port.



Note:

1. If the ADSL LED is off, please check your Internet connection first. Refer to

2.4 Connecting

the Modem Router

for more information about how to make Internet connection correctly. If

you have already made a right connection, please contact your ISP to make sure if your
Internet service is available now.

2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off,

Summary of Contents for TD-W8151N
























































































Search results

Summary of Contents for TD-W8151N

Reviews:

Related manuals for TD-W8151N

Brands by name

Popular brands

TP-Link TD-W8151N, User Manual

Search results

Summary of Contents for TD-W8151N

Reviews:

Related manuals for TD-W8151N

Brands by name

Popular brands