TP-Link L-R480T+ User Manual Download Page 68

Page: 68 / 131

-62-

4.5.2.2

Bandwidth Control

On this page, you can configure the Bandwidth Control function.

Choose the menu

Advanced

→

Traffic Control

→

Bandwidth Control

to load the following page.

Figure 4-31 Bandwidth Control

The following items are displayed on this screen:



Bandwidth Control Rule

Direction:

Select the data stream direction for the entry. The direction of arrowhead

indicates the data stream direction WAN-ALL means all WAN ports

through which the data flow might pass. Individual WAN port cannot be

selected after WAN-ALL rules are added.

Group:

Select the group to define the controlled users.

Mode:

Individual: The bandwidth of each user equals to the current bandwidth

of this entry.

Shared: The total bandwidth of all controlled IP addresses equals to the

current bandwidth of this entry.

Guaranteed

Bandwidth (Up):

Specify the Guaranteed Upstream Bandwidth for this entry.

Limited Bandwidth

(Up):

Specify the Limited Upstream Bandwidth for this entry.

Summary of Contents for L-R480T+




































































































































Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands

TP-Link L-R480T+, User Manual

Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands