TP-Link L-R480T+ User Manual Download Page 41

Page: 41 / 131

-35-



BigPond Status

Status:

Displays the status of BigPond connection.



“Disabled” indicates that the BigPond connection type is not

applied.



“Connecting” indicates that the router is obtaining the IP

parameters from your ISP.



“Connected” indicates that the router has successfully obtained

the IP parameters from your ISP.



“Disconnected” indicates that the connection has been

manually terminated or the router gets no response from your

ISP. Please ensure that your settings are correct and your

network is connected well. Consult your ISP if this problem

remains.

IP Address:

Displays the IP address assigned by your ISP.

Subnet Mask:

Displays the Subnet Mask assigned by your ISP.

Default Gateway:

Displays the IP address of the default gateway assigned by your

ISP.

Note:

To ensure the BigPond connection re-established normally, please restart the connection at least 5

seconds after the connection is off.

4.3.2 LAN

4.3.2.1

LAN

On this page, you can configure the parameters for LAN port of this router.

Choose the menu

Network

→

LAN

→

LAN

to load the following page.

Figure 4-9 LAN

Summary of Contents for L-R480T+




































































































































Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands

TP-Link L-R480T+, User Manual

Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands