TP-Link L-R480T+ User Manual Download Page 31

Page: 31 / 131

-25-

ISP Address:

Optional. Enter the ISP address provided by your ISP. It is null by

default.

Service Name:

Optional. Enter the Service Name provided by your ISP. It is null by

default.

Primary DNS:

Enter the IP address of your ISP’s Primary DNS.

Secondary DNS:

Optional. Enter the IP address of your ISP’s Secondary DNS.

Secondary Connection:

Here allows you to configure the secondary connection. Dynamic IP

and Static IP connection types are provided.

Connection Type:

Select the secondary connection type. Options include Disable,

Dynamic IP and Static IP.

IP Address:

If Static IP is selected, configure the IP address of WAN port. If

Dynamic IP is selected, the obtained IP address of WAN port is

displayed.

Subnet Address:

If Static IP is selected, configure the subnet address of WAN port. If

Dynamic IP is selected, the obtained subnet address of WAN port is

displayed.

Status:

Displays the status of secondary connection.

Upstream Bandwidth:

Specify the bandwidth for transmitting packets on the port.

Downstream Bandwidth:

Specify the bandwidth for receiving packets on the port.

Summary of Contents for L-R480T+




































































































































Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands

TP-Link L-R480T+, User Manual

Search results

Summary of Contents for L-R480T+

Reviews:

Related manuals for L-R480T+

Brands by name

Popular brands