Toyota PT922-12170 Manual Download Page 1

Page: 1 / 24

SCION

2016 -

INTERIOR LIGHT KIT

Preparation

Page 1 of 24 pages

Issue: C 01/28/2016

DIO

Part Number: PT922-12170

Kit Contents

Item #

Quantity Reqd. Description

1 1

Main

Wire

Harness

2 1

Switch

3 1

Switch

Header

4 1

ECU

5 1

ECU

Bracket

6 1

Hardware

Kit

7 1

Instruction

Card

8 1

Light

9 1

Light

Hardware Bag Contents

Item #

Quantity Reqd. Description

Red Scotchlok (16-22 gauge)

Blue Scotchlok (14-18 gauge)

Thin Foam Tape

Thick Foam Tape

25cm Wire Tie

10cm Wire Tie

7 1

Bolt

8 1

Nut

Additional Items Required For Installation

Item #

Quantity Reqd. Description

Conflicts

Premium Audio (Extension Module)

General Applicability

All iM models

Recommended Sequence of Application

Item #

Accessory

Interior Light Controller (for door sills & lights)

2 Interior

Light

Kit

3 Audio
4

*Mandatory

Vehicle Service Parts

(may be required for reassembly)

Item #

Quantity Reqd. Description

Recommended Tools

Personal & Vehicle
Protection

Notes

Safety Glasses

Safety Gloves

Optional

Blankets

Special Tools

Notes

Nylon Panel Removal Tool

Surface Thermometer

Infrared Non-contact

Heat Gun

Master Heat Gun HG-
301A or equivalent

Installation Tools

Notes

Ratchet
Socket 10mm,

12mm

Extension 6”
Torque Wrench

48 in-lbf (5.4 N-m)

Wrench 10mm,

12mm

Pliers Needle

Nose

Side Cutter

Pick Tool

Center Punch

Drill

w/ 6mm bit & drill stop

Hole Deburring Tool

Screwdriver Phillips

Masking Tape

Special Chemicals

Notes

Cleaner

VDC Approved or mild,
water-based solvent free

Legend

STOP:

Damage to the vehicle may occur. Do not

proceed until process has been complied with.

OPERATOR SAFETY:

Use caution to avoid risk of

injury.

CAUTION:

A process that must be carefully observed

in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.

TOOLS & EQUIPMENT:

Used in Figures calls out the

specific tools and equipment recommended for this
process.

REVISION MARK:

This mark highlights a change in

installation with respect to previous issue.

SAFETY TORQUE:

This mark indicates that torque is

related to safety.

Summary of Contents for PT922-12170

























Search results

Summary of Contents for PT922-12170

Reviews:

Related manuals for PT922-12170

Brands by name

Popular brands

Toyota PT922-12170, Manual

Search results

Summary of Contents for PT922-12170

Reviews:

Related manuals for PT922-12170

Brands by name

Popular brands