Toyota Fortuner UH9000S Fitting Instructions Manual Download | Manualshive

Page: 7 / 16

background image

Fitting Instructions

UH9000S / UH9060S / UH9080S

Page 7 of 16

INSTALLATION

Antenna

1.

Remove the sleeve, spacer washer, lock washer and nut
from the antenna.

2.

Pass the antenna cable through the antenna mounting
hole.

3.

Secure the antenna to the mount using the sleeve, spacer
washer, lock washer and nut. Tighten securely.

Antenna Cable

1.

Pass the antenna cable through the radiator grille opening
in the location as shown.

2.

Route the cable through the radiator support panel
opening as shown.

«
...
5
6
7
8
9
...
»

Summary of Contents for Fortuner UH9000S

















Reviews:

No comments

Related manuals for Fortuner UH9000S

Brand: Samsung Pages: 7

MMAC-Plus 9F116-01

Brand: Cabletron Systems Pages: 4

Brand: Caberg Pages: 16

Brand: RaceChip Pages: 20

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 32

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Panasonic Pages: 2

Brand: YOKOGAWA Pages: 15

Brand: SRC Pages: 5

Zeus F745-VTX STACK

Brand: HGLRC Pages: 19

Brand: Mazdaspeed Pages: 8

Brand: EUFAB Pages: 12

Brand: Fisher-Price Pages: 12

Brand: Oasis Pages: 2

Brand: LSL Pages: 4

Brand: MSA Pages: 163

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands