Town & Country Fireplaces Series C Installation And Operating Instructions Manual Download Page 39

Page: 39 / 40

Rating Label Location

NOTE:

The Safety Label is located on a plate found in a slot between the left hand side lintel and the left hand

side window frame. This plate is attached to the lintel with a cable.

FOR OUTDOOR USE ONLY / POUR USAGE EXTÉRIEUR SEULEMENT

Electrical rating:

115v, 60hz, 1.5 A / Note électrique: 115v, 60hz, 1.5 A. This appliance equipped for altitudes 0 - 4500 ft. (0 - 1372 m) / Cet unité est conçu pour

des altitudes variant entre 0 - 4500 pieds (0 - 1372 m). This appliance must be installed in accordance with local codes, if any; if none, follow the current CAN/

CGA-B149 (Canada), or ANSI Z223.1 (USA) Installation Codes. Installer l’appareil selon les codes ou règlements locaux, ou, en l’absence de tels règlements,

selon les codes d’installation CAN/CGA-B149 (Canada), or ANSI Z223.1 (USA) en vigeur. The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with the Canadian Electrical Code, CSA C22.1 or with the National Electrical Code, ANSI/NFPA

70. L’appareil, une fois installé, doit être connecté électriquement à la terre conformément aux codes locaux ou, en l’absence de codes locaux, avec le Code

canadien de l’électricité,CSAC22.1 ou avec le National Electrical Code,ANSI /NFPA70.

WARNING: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. An LP cylinder not connected for

use shall not be stored in the vicinity of this or any other appliance.

AVERTISSEMENT : Ne stockez pas ou utilisez l’essence ou d’autres vapeurs inflammables ou des liquides aux alentours de ceci ou un autre appareil. Un

cylindre LP non connecté pour l’utilisation ne sera pas stocké aux alentours de ceci ou un autre appareil.

FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY / POUR UTILISATION UNIQUEMENT AVEC LES PORTES IN VERRE CERTIFIÉES AVEC

L’APPAREIL

MINIMUM CLEARANCES TO COMBUSTIBLES / CLAIRANCES MINIMALES AVEC LES COMBUSTIBLE

Left and Right side are determined when facing the front of the appliance. / Les côtés droit et gauche se déterminent

en se mettant devant l’appareil et en lui faisant face.

Top, Back and Side Standoffs / Sommet, Arrière et Côté Butée

0 in./ 0 po.

(0 mm)

Sidewall to Appliance / Du mur latéral a l’appareil

4 in./ 4 po.

(102 mm)

Ceiling to Appliance / Plafond a l’appareil

24 in./ 24 po.

(610 mm)

Mantel to Appliance / Du manteau al’appareil

*9 in./ 9 po.

(229 mm)

Maximum Mantel Extension / Allongement maximum du manteau *12 in./ 12 po.

(305 mm)

*See Installation Manual for more detail / Voyez des Directive

de l’Installation pour plus détaux.

Mantel Supports / Supports du manteau

4 in./ 4 po.

(102 mm)

Vent Pipe / Déchargez le Tuyau

1.75 in./ 1.75 po.

(45 mm)

MODEL/

MODELE:

TC36.CODE

SERIES/

SERIE:

FOR USE WITH/

NATURAL GAS/

LP GAS/

EN CASE D’EMPLOI AVEC:

DU GAZ NATUREL DU GAZ LP

Minimum supply pressure / Pression minimum d’alimentation:

5.0 in/wc / 5.0 po/c.e.

12.5 in/wc / 12.5 po/c.e.

(For the purpose of input adjustment / dans le but de régler l’alimenation)

(1.25 kPa)

(3.11 kPa)

Maximum supply pressure / Pression maximum d’alimentation:

13.9 in/wc / 13.9 po/c.e. 13.9 in/wc / 13.9 po/c.e.

(3.45 kPa)

Manifold pressure / Pression de la tuyauterie: Maximum

3.8 in/wc / 3.8 po/c.e.

11.0 in/wc / 11.0 po/c.e.

(.95 kPa)

(2.74 kPa)

Orifice Size / Diametre de l’injectuer:

#30 (3.26 mm)

#45 (2.08 mm)

Input BTU/hr (kW) / Entree BTU/h (kW):

Max.: 47,000 (13.8)

Max.: 47,900 (13.8)

Min.: 35,000 (10.3)

Pacific Energy

Fireplace Products Ltd.

Duncan, British Columbia,

Canada

MADE IN CANADA
FABRIQUE AU CANADA

This Appliance is Equipped For Use With /

Cet Appareil est Équipé Pour Utilise Avec :

NATURAL GAS

GAZ NATUREL

Certified for / Certifié pour Canada and U.S.A.

103013

5050.3601

1-TC36.CODE

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

Refer to the owner’s information manual provided with this appliance. For assistance or additional information, consult a

qualified installer, service agency or the gas supplier.

AVERTISSEMENT: Une installation, un réglage, une modification, une réparation ou un entretien mal effectué peut causer

des dommages matériels ou des blessures. Voir la notice de l’utilisateur qui accompgne l’appareil. Pour de l’aide ou des

renseignements supplémentaires, consultez un installateur, un technicien agréé ou le fournisseur de gaz.

LP-GAS

LP GAZ

Jan.

Feb.

Mar. Apr.

May

June

July

Aug. Sept. Oct.

Nov. Dec.

2013 2014 2015 2016 2017 2018

VENTED OUTDOOR GAS FIREPLACE - NOT FOR USE WITH
SOLID FUEL, FOYER AU GAZ À ÉVACUATION - NE PAS
UTILISER AVEC DU COMBUSTIBLE SOLIDE

ANSI Z21.97-2012 Outdoor Decorative Gas Fireplaces
CSA 2.41-2012 Outdoor Gas Fireplaces

TC36.CODE_271119-40

100003879

Summary of Contents for Series C









































Search results

Summary of Contents for Series C

Reviews:

Related manuals for Series C

Brands by name

Popular brands

Town & Country Fireplaces Series C, Installation And Operating Instructions Manual

Search results

Summary of Contents for Series C

Reviews:

Related manuals for Series C

Brands by name

Popular brands