background image

SERIAL #

271119-40                                                                                                   TC36.CODE                                                                                      100003879-50

MODEL: TC36.OD 
SERIES C
MODULAR DIRECT VENT
FIREPLACE

WARNING:  If the information in these 
instructions is not followed exactly, a fire 
or explosion may result causing property 
damage, personal injury or death.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Installation and service must be performed 
by a qualified installer, service agency or 
the gas supplier.

TC36 OUTDOOR GAS 
FIREPLACE INSTALLATION AND 
OPERATING INSTRUCTIONS

WARNING: 

For Outdoor Use Only

Visit www.townandcountryfireplaces.net for the most recent version of this manual

DANGER: If you smell gas:

1.  Shut off gas to the appliance
2.  Extinguish any open flame.
3.  If odor continues, keep away from the 

appliance and immediately call your gas 
supplier or fire department.

WARNING: Do not store or use gasoline or 
other flammable vapors and liquids in the 
vicinity of this or any other appliance. An 
LP-cylinder not conected for use shall not  
be stored 

WARNING: Improper installation, adjusment, 

alteration, service or maintenance can cause 

injury or property damage. Read the installa-

tion, operating and maintenance instructions 

thoroughly before installing or servicing this 

equipment.

CARBON MONOXIDE HAZARD

This appliance can produce carbon 
monoxide which has no odor.
using it in an enclosed space can 
kill you.
Never use this appliance in an 
enclosed space such as a camper, 
tent, car or home.

Summary of Contents for Series C









































Reviews: