background image

tousek

  /  EN_ST-12-5_05  /  25. 03. 2020 

- 13 -

 

Photocell function inside 

Safety

 

during closing reverse: 

an interruption of the photocell during closing makes the gate reverse (open). In automatic 

mode the gate closes as soon as the pause time has run out. In impulse operation another closing command has to 

be given.

 

stop - after release open: 

an interruption of the photocell beam during opening or closing makes the motor stop as 

long as the photocell stays interrupted. After release of the photocell, the gate opens. In automatic mode the gate closes 

as soon as the pause time has run out, in impulse operation another closing command has to be given.

 

during opening stop - then open:  

an interruption of the photocell during opening makes the motor stop as long as 

the photocell stays interrupted. After release of the photocell, the gate opens (back area monitoring). In automatic mode 

the gate closes as soon as the pause time has run out, in impulse operation another closing command has to be given.

 

Photocell function outside 

Safety

 

during closing reverse: 

an interruption of the photocell during closing makes the gate reverse (open). In automatic 

mode the gate closes as soon as the pause time has run out. In impulse operation another closing command has to 

be given.

 

stop - after release open: 

an interruption of the photocell beam during opening or closing makes the motor stop as 

long as the photocell stays interrupted. After release of the photocell, the gate opens. In automatic mode the gate closes 

as soon as the pause time has run out, in impulse operation another closing command has to be given 

 

PHC-pause time 

Safety

 

no influence of photocell

the photocell doesn’t have any influence on the pause time in automatic mode.

 

abort pause time: 

in automatic mode an interruption of the photocell during pause time shortens the pause time. After 

release of the photocell the gate starts closing.

 

re-start of pause time: 

in automatic mode an interruption of the outer photocell during pause time, restarts the pause 

time. As soon as the pause time has run out, the gate closes.

 

immediate close after opening: 

If the photocell is interrupted during the opening movement, the gate starts closing 

as soon as it reached end position open after release of the photocell.

  

PHC-self test 

Safety

 

active: 

photocell self-test is executed with an opening impulse (switch, button) in gate position „closed“.   

 

not active:  

photocell self-test is not executed

 

 Attention

• 

The photocell self-test can only be deactivated by selecting „not active“.

• 

The deactivation of the self-test function is only permitted if the safety installations correspond to the 

category 3 !

PHOTOCELL FUNCTIONS 

Safety

Summary of Contents for ST 12/5

































Reviews: