Toto WASHLET MS922CUMFG Instruction Manual Download

Page: 18 / 60

3. Open the shutoff valve

Remove the side

panel (left).

Fully open the shutoff valve.

Handle

(For opening or closing

the shutoff valve)

Shutoff

valve

*1 Installed on the back of the side panel

(on the left).

Reinstall the side

panel.

•

Fit the side panel to the

top and side of the bowl

unit without a gap.

Side of the bowl unit

Top of the

bowl unit

2. Turn on the power

Insert the power plug.

• The wand extends and then retracts.

Check that the "Power" LED

lights up.

• When it is off , switch the "Power" to

"ON".

To operate from the back of remote control

Press "Power ON/OFF" button for about

3 seconds or longer.

To operate from the front of remote control

• Recommended if the remote control is

secured to prevent theft.

Press "Oscillating washing" button

about 10 seconds or longer.

<Power>

To turn the power "OFF"

Perform the same operation as step

above.

• The "Power" LED goes off .

Introduction

Summary of Contents for WASHLET MS922CUMFG





























































Search results

Summary of Contents for WASHLET MS922CUMFG

Reviews:

Related manuals for WASHLET MS922CUMFG

Brands by name

Popular brands

Toto WASHLET MS922CUMFG, Instruction Manual

Search results

Summary of Contents for WASHLET MS922CUMFG

Reviews:

Related manuals for WASHLET MS922CUMFG

Brands by name

Popular brands