background image

Cleaning the urinal

For light dirt

Wash with water using a cleaning brush or sponge.

For scale or heavy dirt

Routine Maintenance

Maintenance keeps the toilet clean and extends its service life. Please perform thorough and 
routine maintenance. Note that although CeFiONtect parts have dirt prevention properties, 
routine maintenance is still important to keep their surfaces clean.

[Cleaning the porcelain main unit/drain trap]

Wear rubber gloves when removing and cleaning 
the drain trap.

About the cleaning detergent

Any commercially available household detergents can be 
used, regardless of whether they are acidic, neutral or 
alkaline.
However, do not use detergents that repel water.
Using these could cover the porcelain surface, causing 
some parts not be cleaned.
Also, do not use detergents containing abrasive 
compounds, industrial strongly acidic or strongly alkaline 
detergents, or fluorine-based detergents

*1

, because they 

may damage or permeate the porcelain surface.

* Rinse thoroughly so that no detergent remains.
* 1 Including hydrogen fluoride and ammonium fluoride

About the cleaning tools

Do not use tools such as wire brushes, abrasive nylon 
scrubbing pads or sandpaper, because they will damage 
the surface.

About CeFiONtect

CeFiONtect is TOTO independently developed technology 
where bumps on the porcelain surface are smoothed at 
the nano level of 1 million of 1 mm, making dirt difficult to 
adhere and easy to remove.

About surface coating agents

Do not use any water repellant, stain-proofing detergent 
or surface coating agent. 
These products do not damage the porcelain surface, 
but their components may cover the porcelain surface 
and reduce the effect of the built-in stain prevention 
technology.

Place a towel, etc. over the photoelectric sensor

Photoelectric sensor stops detecting

Remove the towel, etc. (recovers automatically)

WARNING

Prohibited

Do not wash the entire product with water

Doing so may cause a malfunction or current leak.

Required

Handle with care, because this is an 
electric appliance

Failure to do so may cause an electrical shock.

Advice for cleaning the inside bowl surface

When cleaning the inside bowl surface, use a towel, etc. to stop flushing water.

Wipe off moisture from 
the dirty part.

Apply toilet cleaner 
directly on the dirt.

Scrub using a cleaning brush or sponge.

As the final step, wash 
with water.

If the dirt is difficult to remove, 
use a tool such as a small 
stick to scrape it away.

Wire brush

Sandpaper

Towel, etc.

Components of detergent 
or coating agent cover the 
CeFiONtect surface.

CeFiONtect

Abrasive nylon 
scrubbing pad

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

Detergent containing 
abrasive compounds

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

For industrial

use

Acidic

detergent

Neutral

detergent

Alkaline

detergent

For industrial

use

Fluorine-based 
detergent *1

Strongly acidic or strongly 
alkaline detergent

Water-

repellent 

detergent

Water-repellent 
detergent

Usable detergents for porcelain 

main unit cleaning

Acidic detergent

Neutral detergent

Alkaline detergent

8

9

Ma
in

ten
a

nc
e

Summary of Contents for USWN925 Series












Reviews: