manualshive.com logo in svg

Total Control Systems 700-LP Series, Installation, Operation & Maintenance Manual

Share
Download
Total Control Systems 700-LP Series Installation, Operation & Maintenance Manual Download Page 33

Page 33 

  

Reassembly of Meter 

Reinstalling Packing Capsule & Front/Rear Covers 
 

1)  Reinstall cover O-rings on the front and rear of meter housing. 
2)  Reinsert packing capsule into front cover of meter with retaining plate and tighten screws. 
3)  When attaching front cover, align packing capsule blade with the slot on the blocking rotor sleeve. Tighten all 

front cover screws. 

4)  Attach rear cover and tighten all screws. 

Reinstalling Counter Support & Adjustor Drive Shaft 

 

1)  Position the counter support on the front side of meter and tighten all screws. 
2)  Reinsert  adjustor  drive  shaft into the  support  housing  and  assure  that  adjustor  face  gear teeth  mesh  with  the 

packing capsule gear.  Do not fit the face gear and packing gear too tight! 

3)  Slide down the adjustor mounting bracket and tighten the screws. 

1 

2 

3 

4 

1 

2 

3 

Summary of Contents for 700-LP Series

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands