Toshiba TDP-P6 Manual Download Page 7

Page: 7 / 75

TDP-P6 Service Manual

Power Diagnostics, Part 1

Plug the projector into a good power

source with a known good power cord.

Replace the power

supply (page 55)

No, the

fans

started but

the LED

did not light

Yes

Replace controller ECA

(page 43)

Replace power

supply (page 54)

Voltages OK?

Solid green

This is the
normal
condition.

Do the fans

run briefly and

the LED light?

No, the

fans

did not

start and

the LED

did not

light.

Red

Go to Power

Diagnostics, part 2

(page 8)

Go to Error

Codes

(page 9)

This is the normal condition.

LED light

green or red?

Confirm that unit is good

by starting again.

Confirm that unit is

good by starting again.

Power Diagnostics, part 1

Solve the
problem?

Yes

Replace top enclosure

(includes keypad ECA)

(page 31)

Note

A solid green
LED

means the

projector is either
waiting for a
command or is
operating
normally.

A flashing green
LED

means the

projector is either
attempting to
light the lamp or
is shutting down.

Check the voltages at the

controller/power supply

connector. (page 16)

Confirm that the

keypad cable is

plugged in.

Ensure that the lamp door

is present and shut. The

lamp door has an interlock
connector that plugs into a

receptacle under the lamp

door. If the connector does

not mate properly with the

receptacle, the projector

will not power up. Make

sure that the connector and
receptacle are present and

in fucntional condition.

Summary of Contents for TDP-P6












































































Search results

Summary of Contents for TDP-P6

Reviews:

Related manuals for TDP-P6

Brands by name

Popular brands

Toshiba TDP-P6, Manual

Search results

Summary of Contents for TDP-P6

Reviews:

Related manuals for TDP-P6

Brands by name

Popular brands