Toshiba TDP-P6 Manual Download Page 67

Page: 67 / 75

TDP-P6 Service Manual

Connect the following to the I/O panel on the projector:

♦

Video player through the S-video connector.

♦

Computer through the M1-A connector

Perform the following tests

Test

Verification

Power Up

Connect AC power, and turn
the unit on.

Verify that the proper splash (logo) screen appears. If the incorrect logo
screen appears, you must install the proper brand system software. The
logo screen is automatically installed when you do this.
Verify image quality.

Cosmetics and mechanicals

Adjust the projector so that the
image is square. Make sure
the lens is at a 90° angle to
the wall.

Verify that the elevator and leveling foot are functional.
Verify that the focus and zoom rings operate properly.
Verify cosmetics.

Video source

On the

keypad

, press the

Video

button display the S-

video source.

Verify that the video automatically synchronizes. If it doesn't, press the

Video

button on the keypad.

Verify there is no distortion, noise or other abnormalities.
Verify that the audio plays clearly.

Audio from video source

Verify that the audio is clear with no distortion.

Software Version / Keystone
/ Reset All

1. Press and hold the

Keystone up

and

Keystone down

button on the keypad.

2. Press

the

Menu

button, and then
navigate to

About

3. Navigate to Main >

Settings > Service.
Select

Factory Reset

Verify that the keystone adjustment works properly.

Verify software version in the About box.

Verify the keys are not sticky.

Summary of Contents for TDP-P6












































































Search results

Summary of Contents for TDP-P6

Reviews:

Related manuals for TDP-P6

Brands by name

Popular brands

Toshiba TDP-P6, Manual

Search results

Summary of Contents for TDP-P6

Reviews:

Related manuals for TDP-P6

Brands by name

Popular brands