RS232C Command List for TOSHIBA DLP Projector TDP-D1
Rev. K 2003.1.7
Reply of Error List Command
Ascii
Ascii
Data1
Data2
Data3
Data4
Data5
Data6
Data7
Data8
Data9
Data10
Data11
Data12
Data13
Data14
Data15
Data16
Data17
Data18
Data19
ACK
CR
Shutdown
Count
Lamp Error
Count
Fan 1
Speed Error
Count
Fan 2
Speed Error
Count
Fan 3
Speed Error
Count
Fan 1 Temp.
Error Count
Fan 2 Temp.
Error Count
Fan 3 Temp.
Error Count
Device Error
Count
Error Log 1
Error Log 2
Error Log 3
Error Log 4
Error Log 5
Error Log 6
Error Log 7
Error Log 8
Error Log 9 Error Log 10
New <------
------> Old
Description
Lamp Error Count
The count of the lamp error. This error will occur, if the LAMPLIT signal is low.
Fan X Speed Error Count The count of the fan speed error. This error will occur, if the speed of the fan x is too low.
Fan X Temp Error Count The count of the fan temp error. This error will occur, if the temperature of the fan x is too high.
Device Error Count
The count of the device error. This error will occur, if devices are wrong. (ex: Video decoder reset error)
Error Log [10]
The log list of error. The error log [1] is the newest.
Error Type
Number for Error Log
Lamp Error
1
Fan 1 Speed Error
2
: Lamp Fan
Fan 2 Speed Error
3
: Ballast Fan
Fan 3 Speed Error
4
: Blower Fan
Fan 1 Temp. Error
5
: DMD Temp.
Fan 2 Temp. Error
6
: Lamp Temp.
Fan 3 Temp. Error
7
: Fan Board Temp.
Device Error
8
Reply of Lamp (Time) List Command
Ascii
Ascii
Data1
Data2
Data3
Data4
Data5
Data6
Data7
Data8
Data9
Data10
Data11
Data12
Data13
Data14
Data15
Data16
Data17
Data18
Data19
Data20
Data21
Data22
ACK
CR
New <------
------> Old
Description
Reset Count
The count of user reset.
Reset Time [10]
The time list of user reset. This shows the time interval of reset. The reset time [1] is the newest.
Reply of Burn In Timer Command
Ascii
Ascii
Data1
Data2
Data3
Data4
ACK
CR
Minutes
Seconds
Reset Time 9 (MSB 1st)
Reset Time 10 (MSB 1st)
Reset Time 4 (MSB 1st)
Reset Time 5 (MSB 1st)
Reset Time 6 (MSB 1st)
Reset Time 7 (MSB 1st)
Reset Time 2 (MSB 1st)
Reset Time 3 (MSB 1st)
Hours (MSB 1st)
Reset Time 8 (MSB 1st)
Reset Count
Reset Time 1 (MSB 1st)
74
Summary of Contents for TDP-D1
