Toshiba SD-22VB Service Manual Download Page 7

Page: 7 / 111

To return to the initial sharpness setting, press CANCEL
while the sharpness setting screen is appearing.

Note:

Playback sharpness

Adjust the sharpness of playback picture during
playback. During slow motion, still picture and picture
search, sharpness-adjusting is impossible.

TIMER REC SET

AUTO REPEAT

CHANNEL SETUP

SYSTEM SETUP

SELECT :

ENTER : ENTER

EXIT

VCR SETUP

[OFF]

Press VCR MENU repeatedly until the TV picture
appears on the screen.

Press VCR MENU.
Press

to select

VCR SETUP. Then press
ENTER.

Press

to select

PLAYBACK SHARP-
NESS. Then press
ENTER.

Press

to adjust

the playback sharpness
to the level you reguire.

AUDIO MIX

NICAM

VCR SETUP

SELECT :

ENTER : ENTER

EXIT

PLAYBACK SHARPNESS

[OFF]

[AUTO]

PLAYBACK SHARPNESS

+ Ð Ð + Ð Ð + Ð Ð + Ð Ð

SET

CANCEL

CENTRE :

EXIT :

softer sharper

Special playback/Playback sharpness/Skip Search

Adjusting tracking condition

Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.

Notes:
• The audio output is muted during SPEED SEARCH,

STILL, FRAME ADVANCE and SLOW MOTION.

• During picture search mode there will be noise bars

which are caused by the system.

• The Special Playback will automatically change to

playback after approx. 5 minutes to protect the video
tape against excessive wear.

Automatic tracking adjustment

If automatic tracking cannot eliminate noises well during
playback, press SET + or SET – to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine
adjustment, or press and hold for a coarse adjustment.

Manual tracking adjustment

To return to automatic tracking, press A. TRK.

Special playback

Slow Motion
During playback press SLOW.
You can change the slow speed by the additional
pressing of SLOW.
To return to playback: Press PLAY.

Reverse picture search function
Press REW x 1 or x 2 during the playback.

Picture Search

Forward picture search function
Press FWD x 1 or x 2 during the playback.
To return to playback: Press PLAY.

Still Picture
Press PAUSE/STILL during playback. To resume
normal playback: Press PLAY.

During playback, press PAUSE/STILL one by one:
The picture advances frame by frame.
To return to playback: Press PLAY.

Frame by Frame picture

Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion,
press the SET + or – to reduce the noise bars.
If the still picture jitters excessively, press SET + or –
to stabilize the still picture.

Skip Search
Each time you press INSTANT SKIP while a tape is playing,
the unit will fast-forward ahead 30 seconds on the tape. You
may press the button up to six times in a row to move 180
seconds (three minutes) ahead.

For example: 1 press:

Approx. 30 seconds of tape

2 presses: Approx. 60 seconds of tape
3 presses: Approx. 90 seconds of tape

Start the playback of video tape.

Repeat Playback

Note:
To cancel the auto repeat mode, follow the
above steps 1 and 2, then select "OFF"
and confirm by pressing VCR MENU.

If the Repeat function is switched
on, the playback will continue until
it reaches the tape-end and then
rewind to the beginning of the tape.
This process will repeat until the
unit is turned off.

To set the Repeat function

• Turn on the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode.

Preparation

Press VCR MENU repeatedly until the TV picture appears.
If "ON" has been selected, the tape will be repeatedly
played.

Press VCR MENU.
Press

▲

▼

to select the AUTO
REPEAT.

Press

to select

[ON] or [OFF].

SELECT :

CHANNEL SETUP

ENTER

EXIT

: ENTER

: MENU

VCR SETUP

AUTO REPEAT

SYSTEM SETUP

TIMER REC SET

SELECT :

CHANNEL SETUP

ENTER

EXIT

: ENTER

: MENU

VCR SETUP

AUTO REPEAT

OFF

SYSTEM SETUP

TIMER REC SET

SLOW

PAUSE/STILL

SET Ð

INDEX Ð SKIP INDEX +

SET UP

VCR MENU

ENTER

CANCEL

VIDEO Plus+

A-B RPT

INSTANT SKIP

ZERO RETURN

TITLE

SET +

CH +

CH Ð

OPEN/CLOSE

ANGLE

COUNTER RESET

AUDIO

AUDIO SELECT

SUBTITLE

ATR

PLAY MODE

SP/LP

DISPLAY

CALL

TIMER REC

CLOCK

COUNTER

DVD

VCR

ZOOM

AUX

TV/VCR

MEMORY

REC/OTR

RETURN

E.A.M

PLAY

REW

FWD

STOP

Preparation:
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)

Press DISPLAY.
The counter display shows the
tape running time during
playback or recording.
The Recorder will indicate REC
during recording for itself.

Press COUNTER RESET at the
desired tape position.
The counter display will be reset
to the "00:00:00" position (e.g.
the beginning of recording).

Press STOP when playback or recording is finished.
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically
stop at the ”00:00:00” position.

Press DISPLAY once again to make the all indicator disappear.

The CLOCK COUNTER button
Press CLOCK COUNTER during the playback. The clock and tape
counter alternate with each other in the display.

Note:
You can set the tape counter to 00:00:00 with COUNTER RESET
anytime. Therefore, the counter display can also indicate 00:00:00,
even when the tape counter does not reach its beginning yet. Even if
the tape counter indicates 00:00:00, it can be rewinded moreover. If
the tape was rewinded over the point of 00:00:00, the minus mark (–
) appears in the counter display. Although the tape counter seems to
forward when you press REW, in fact the tape is being rewinded.
When the tape reaches the beginning, the tape-rewinding stops
automatically.

Counter Display

ZERO RETURN function
This function makes tape-rewinding
stop at the counter 00:00:00 position
automatically.

Notes:
• When you load a video cassette, the dis-

play indication changes to "00:00:00".

• The counter display does not function

on non-recorded (blank) sections of the
tape. When you rewind, fast forward or
play tapes through blank sections, the
counter display stops.

CH 2

12:00 SUN

00:04:38 SP

CH 2

12:00 SUN

00:00:00 SP

SLOW

PAUSE/STILL

SET Ð

INDEX Ð SKIP INDEX +

SET UP

VCR MENU

ENTER

CANCEL

VIDEO Plus+

A-B RPT

INSTANT SKIP

ZERO RETURN

TITLE

SET +

CH +

CH Ð

OPEN/CLOSE

ANGLE

COUNTER RESET

AUDIO

AUDIO SELECT

SUBTITLE

ATR

PLAY MODE

SP/LP

DISPLAY

CALL

TIMER REC

CLOCK

COUNTER

DVD

VCR

ZOOM

AUX

TV/VCR

MEMORY

REC/OTR

RETURN

E.A.M

PLAY

REW

FWD

STOP

VCR

S P

VCR

S P

VCR

S P

VCR

S P

Video Index Search System

Whenever a recording is begun an
invisible index mark is recorded on the
tape. These index marks are all identical,
and each mark means: "Here starts a
new recording". Every DVD/VCR
equipped with the Video Index Search
System (VISS) can locate these marks
at the beginning of any recording.

Example: Indexing of TV commercials.

Start playback and wait until
the end of the TV commercial
is reached, then press STOP.

Press REC/OTR. When the "INDEX" on-screen indication
goes off, STOP may be pressed. This short recording
process will be sufficient to set an index mark.
This will result in about 10 seconds of the TV commercials to
be overwritten by another recording. Due to the system the
end of this recording will be followed by a recording gap (noise
signal) of approx. 5 seconds.

Recording several Index Marks
Due to the system only one index mark will be recorded at the

beginning of a recording. If you intend to set several index
marks during a single recording, follow the procedure below:

At the point of the recording
where an index mark is to be
set press PAUSE/STILL. The
unit will switch to the recording
pause mode.

Press CH repeatedly to switch
back to the original TV
program. Press PAUSE/STILL
to resume recording.

Index Search
Press INDEX + or – during stop
or play mode.
For Succeeding programs:
Press INDEX +.
For Preceding programs:
Press INDEX –.
(Additional press increases the
INDEX NO. up to 9.)
When the INDEX + or – is
pressed, the unit starts
searching the INDEX NO.
selected and finds the portion,
then playback starts automati-
cally.
To stop the Index Search, press
STOP.

CH 2

INDEX

Notes:

When you record an INDEX mark at
the very beginning of the tape, the
mark may not be found.
During INDEX search, the tape may
stop and begin to play at a slightly
different location.
INDEX may not function properly with
old or worn out video tapes.
INDEX marks may not be found if it is
extremely close to the point where the
search began.
In recording, if you stop recording tem-
porarily, the INDEX mark is not re-
corded on the tape.

•

INDEX NO. (up to 9)

is displayed

SLOW

PAUSE/STILL

SET Ð

INDEX Ð SKIP INDEX +

SET UP

VCR MENU

ENTER

CANCEL

VIDEO Plus+