Toshiba Satellite P770 Manual Download | Manualshive

Page: 75 / 281

background image

2Troubleshooting Procedures

Satellite P770/P775 Series Maintenance Manual

39

The HDD/SSD or system board may be the reason of a HDD/SSD fault. Either of these two

components may be damaged. To determine if the computer’s HDD/SDD is functioning

properly, perform the following procedures. Figure 2-14 outlines the process. Start with

Procedure 1 and continue with the other procedures as instructed.

Procedure 1: Diagnostic test

Procedure 2: Connector and replacement check

Procedure 1

Diagnostic test

Run the Diagnostic Program, which will automatically execute the HDD/SSD R/W test.
(Refer to Chapter 3 system configuration check), Tests and Diagnostics for more information
on the program.

If an error is located, go to Procedure 2. If an error is not located, the HDD/SSD function is
functioning properly.

Procedure 2

Connector and replacement check

The HDD module or system board may be disconnected or damaged. Disassemble the
computer following the steps described in Chapter 4,

Replacement Procedures

, and perform

the following checks.

Check 1

Make sure that the HDD module is securely slotted into the system board. If the
problem persists, go to Check 2.

Check 2

The HDD module may be damaged. Replace it with a new one following the
instructions in Chapter 4. If the problem still exists, perform Check 3.

Check 3

The system board may be damaged. Replace it with a new one following the
instructions in Chapter 4.

«
...
73
74
75
76
77
...
»

Summary of Contents for Satellite P770


























































































































































































































































































Reviews:

No comments

Related manuals for Satellite P770

Brand: NEO Pages: 31

Intel PRO/100 SP

Brand: IBM Pages: 72

Brand: BELINEA Pages: 48

TravelMate P4 14

Brand: Acer Pages: 93

TravelMate P2 14

Brand: Acer Pages: 88

Brand: Acer Pages: 82

Brand: Acer Pages: 83

Brand: Hyundai Pages: 24

Brand: Dell Pages: 75

Brand: AWOW Pages: 17

Brand: AWOW Pages: 36

Aspire F 15 Touch

Brand: Acer Pages: 77

A10 S129 - Satellite - Celeron 2.4 GHz

Brand: Toshiba Pages: 9

Brand: Sony Pages: 2

MZ-R30 Analog PCLink

Brand: Sony Pages: 2

Brand: Sony Pages: 16

Brand: Sony Pages: 20

Brand: Sony Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands