Toshiba Satellite P770 Manual Download | Manualshive

Page: 65 / 281

background image

2 Troubleshooting Procedures

Satellite P770/P775 Series Maintenance Manual

29

Procedure 4

Connection check and replacement check

The optical drive connects to the system board. The drive may be disconnected, or the drive
or system board may be damaged. Disassemble the computer following the steps described in
Chapter 4,

Replacement Procedures

, and perform the following checks:

Check 1

Make sure the drive is firmly connected to the system board. If the connection is
good and there is still an error, go to Check 2.

Check 2

The drive or drive cable may be defective or damaged. Replace each with a new
one following the steps in Chapter 4,

Replacement Procedures

. If the drive is still

not functioning properly, perform Check 3.

Check 3

The system board may be damaged. Replace it with new one following the
instructions in Chapter 4, Replacement Procedures.

«
...
63
64
65
66
67
...
»

Summary of Contents for Satellite P770


























































































































































































































































































Reviews:

No comments

Related manuals for Satellite P770

Brand: IBM Pages: 2

Brand: IBM Pages: 5

Brand: IBM Pages: 6

600E - ThinkPad 2645 - PII 400 MHz

Brand: IBM Pages: 222

Brand: BenQ Pages: 32

AcerNote Light 370

Brand: Acer Pages: 16

Brand: Acer Pages: 28

Acer TravelMate 3300 Series

Brand: Acer Pages: 75

Brand: Acer Pages: 88

AcerNote Light 370

Brand: Acer Pages: 3

Aspire 1360 Series

Brand: Acer Pages: 143

Brand: Acer Pages: 11

Brand: Acer Pages: 79

AS7315-302G25Mn

Brand: Acer Pages: 200

AS4810T- 354G32Mn LX.PBA0X.075

Brand: Acer Pages: 148

Brand: Acer Pages: 69

Brand: Acer Pages: 224

Brand: Acer Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands