Toshiba Satellite P770 Page 91 Manual Download | Manualshive

Page: 91 / 281

background image

2Troubleshooting Procedures

Satellite P770/P775 Series Maintenance Manual

55

The system board may be the reason of a Sleep & Play music fault. The system board may be

damaged. To determine if the computer’s Sleep & Play music is functioning properly,

perform the following procedures. Figure 2-22 outlines the process. Start with Procedure 1

and continue with the other procedures as instructed.

Procedure 1: windows application test

Procedure 2: Replacement check

Procedure 1

windows application test

Test Sleep & Play music function with Audio loopback line and Multimedia sound system
with line in and line out port, check the device can work fine or not.

If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the Sleep
& Play music functioning is properly.

Procedure 2

Replacement check

Disassemble the computer following the steps described in Chapter 4,

Replacement

Procedures

, and perform the following checks.

Check 1

Make sure that Sleep & Charge test operation is correct, go to Check 2.

Check 2

The system board may be damaged. Replace it with a new one following the
instructions in Chapter 4.

«
...
89
90
91
92
93
...
»

Summary of Contents for Satellite P770


























































































































































































































































































Reviews:

No comments

Related manuals for Satellite P770

Laptop Master MFC105GBZ

Brand: LEXIBOOK Pages: 27

Brand: Gateway Pages: 12

M190S World Warrior

Brand: EUROCOM Pages: 149

TravelMate 4750

Brand: Acer Pages: 315

TravelMate 520 Series

Brand: Acer Pages: 83

Brand: Dell Pages: 46

Latitude 3310 2-in-1

Brand: Dell Pages: 39

S7220 - LifeBook - Core 2 Duo 2.4 GHz

Brand: Fujitsu Pages: 208

Satellite Pro S300M-W3401V

Brand: Toshiba Pages: 5

Satellite Pro S300M-S2142

Brand: Toshiba Pages: 5

Satellite Pro S300M-EZ2421

Brand: Toshiba Pages: 5

Satellite Pro S300-S2503

Brand: Toshiba Pages: 5

Satellite Pro S300-S2504

Brand: Toshiba Pages: 5

Satellite Pro S300-S1001

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ2521

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ2502

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ1514

Brand: Toshiba Pages: 5

Satellite Pro S300-EZ1513

Brand: Toshiba Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands