manualshive.com logo in svg

Toshiba Satellite P770, Manual, Page: 238 / 281

Share
Download
Toshiba Satellite P770 Manual Download Page 238

C.9  JWLAN 

Table C-9 WLAN Connector pin assignments (52-pin) 

Pin No. 

Signal name 

I/O 

Pin No. 

Signal Name 

I/O 

A1 NA 

  A2 +3V_WLAN 

 

A3 NA 

  A4 GND 

 

A5 BT_CTRL_R 

  A6 +1.5VS 

 

A7 CLKREQ_WLAN#    A8 NA 

 

A9 GND 

  A10 NA 

 

A11 CLK_WLAN# 

  A12 NA 

 

A13 CLK_WLAN 

  A14 NA 

 

A15 GND 

  A16 NA 

 

A17 NA 

  A18 GND 

 

A19 NA 

  A20 WL_OFF# 

 

A21 GND 

  A22 PLT_RST# 

 

A23 PCIE_PRX_WLAN

TX_N2 

 A24 

+3V_WLAN 

 

A25 PCIE_PRX_WLAN

TX_P2 

 A26 

GND 

 

A27 GND 

  A28 +1.5VS 

 

A29 GND 

  A30 PM_SMBCLK 

 

A31 PCIE_PTX_C_WL

ANRX_N2 

 A32 

PM_SMBDATA 

 

A33 PCIE_PTX_C_WL

ANRX_P2 

 A34 

GND 

 

A35 GND 

  A36 USB20_N9 

 

A37 GND 

  A38 USB20_P9 

 

A39 +3V_WLAN 

  A40 GND 

 

A41 +3V_WLAN 

  A42 LED_WIMAX# 

 

A43 GND 

  A44 NC 

 

A45 NC 

  A46 NC 

 

A47 NC 

  A48 +1.5VS 

 

A49 N32750573 

  A50 GND 

 

A51 E51_RXD_R 

  A52 +3V_WLAN 

 

 

 

 

 

C-6                        

[CONFIDENTIAL]

 

Satellite P770/P775 

Series Maintenance Manual 

Summary of Contents for Satellite P770


























































































































































































































































































Reviews:

No comments