Toshiba Satellite A350 Series Maintenance Manual Download Page 239

Page: 239 / 297

4 Replacement Procedures

Error! Style not defined. Error! Style not defined.

4.27

Bluetooth Card

Removing the Bluetooth card

Remove the Bluetooth card according to the following procedures and Figure 4.47.

Remove the Bluetooth cable from the Bluetooth card.

Press down the latch and push the Bluetooth card in the direction indicated in the figure
4.47 and slide the Bluetooth card out.

Remove the card from the logic lower assembly.

Figure

47 Removing the Bluetooth card

Note: Be careful not to damage the Bluetooth Card when connecting it with the cable. Make
sure the card is seated in the correct position.

Satellite A350D Maintenance Manual

4-62

Downloaded from LpManual.com Manuals

Summary of Contents for Satellite A350 Series










































































































































































































































































































Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands

Toshiba Satellite A350 Series, Maintenance Manual

Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands