Toshiba Satellite A350 Series Maintenance Manual Download Page 230

Page: 230 / 297

Error! Style not defined. Error! Style not defined.

4 Replacement Procedures

Remove six M2x3 screws that secure the LCD hinge assembly to the LCD panel and then
remove the LCD hinge assembly.

Figure

39 Removing the LCD Hinge Assembly

Turn the LCD module over and place it face down on a protective surface, such as a foam
pad.

Remove the tape and VLDS cable connector. Then detach the VLDS cable.

Satellite A350D Maintenance Manual

4-53

Downloaded from LpManual.com Manuals

Summary of Contents for Satellite A350 Series










































































































































































































































































































Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands

Toshiba Satellite A350 Series, Maintenance Manual

Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands