Toshiba Satellite A350 Series Maintenance Manual Download Page 28 | Manualshive

Page: 28 / 297

background image

Error! Style not defined. Error! Style not defined.

1 Hardware Overview

1.2

2.5-inch HDD

The computer contains an extremely low-profile and lightweight, high-performance HDD. The
HDD incorporates 9.5 mm / 12.5 mm height magnetic disk and mini-Winchester type magnetic
heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 120, 160,
250, 320, 400, and 500 GB.

The HDD is shown in Figure 1-2 and some of its specifications are listed in Table 1-1.

Figure 1-2

SATA HDD

Table 1-1

HDD Specifications

Item

Specifications

Capacity (GB)

120GB

160 GB

250 GB

320G

Rotational
Speed (RPM)

5400 RPM

5400 RPM

5400 RPM

5400 RPM

Height

9.5 mm

9.5 mm

9.5 mm

9.5 mm

User Data
Sectors

234,441,648 312,581,808

488,397,168 625,142,448

Bytes / Sector

512 512

512

512

Satellite A350D Maintenance Manual

1-11

Downloaded from LpManual.com Manuals

«
...
26
27
28
29
30
...
»

Summary of Contents for Satellite A350 Series










































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A350 Series

Satellite C50-K

Brand: dynabook Pages: 46

Brand: MSI Pages: 102

Brand: TONGFANG Pages: 44

TravelMate 3010

Brand: Acer Pages: 94

TravelMate 3010

Brand: Acer Pages: 94

TravelMate 3200 Series

Brand: Acer Pages: 92

TravelMate 3030 Series

Brand: Acer Pages: 100

TravelMate 3200 Series

Brand: Acer Pages: 92

TravelMate P645-M

Brand: Acer Pages: 85

TravelMate C210 Series

Brand: Acer Pages: 97

TravelMate P243-MG

Brand: Acer Pages: 84

TravelMate B113-M

Brand: Acer Pages: 217

TravelMate P278-M

Brand: Acer Pages: 74

TravelMate C310 Series

Brand: Acer Pages: 69

Alienware 15 R3

Brand: Dell Pages: 29

Brand: HP Pages: 32

Compaq nx5000 series

Brand: HP Pages: 48

Brand: HP Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands