Toshiba Satellite A350 Series Maintenance Manual Download Page 108

Page: 108 / 297

2 Troubleshooting Procedures

Satellite A350D/A355D, SATEGO A350D, EQUIUM A350D Series Maintenance Manual

Figure 2-20 SPDIF troubleshooting process

The system board may be the reason of a SPDIF fault. The connector of system board may be

damaged. To determine if the computer’s SPDIF is functioning properly, perform the

following procedures. Figure 2-20 outlines the process. Start with Procedure 1 and continue

with the other procedures as instructed.

Procedure 1: Diagnostic test

Procedure 2: Connector and replacement check

Procedure 1

Diagnostic test

If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the

SPDIF is functioning properly.

Procedure 2

Connector and replacement check

The system board may be disconnected or damaged. Disassemble the computer following the
steps described in Chapter 4, Replacement Procedure

, and perform the following checks.

Check 1 the system board may be damaged. Replace it with a new one following the

instructions in Chapter 4.

Downloaded from LpManual.com Manuals

Summary of Contents for Satellite A350 Series










































































































































































































































































































Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands

Toshiba Satellite A350 Series, Maintenance Manual

Search results

Summary of Contents for Satellite A350 Series

Reviews:

Related manuals for Satellite A350 Series

Brands by name

Popular brands