Toshiba PDR-M500 Service Manual Download | Manualshive

Page: 16 / 49

background image

19

Install the Jack Cover
ASSY A250 as shown.
Assemble the Front
Cover ASSY A100 to
camera. Check the
position of Power
Switch first.

The Microphone
ASSY H320
might be inserted
on the Front
Cover ASSY.

20

Connect the wire of
Microphone ASSY
H320 to camera. Drive
the screw 01635-000 as
shown.

Screw driver
Tweezers

21

Install the Flex Cable
Main-LCD H600 on the
camera.

Tweezers

22

Drive the screws 01635-
149 of Tripod Holder
A340.

Screw driver

23

Install the Mode Dial
ASSY A410 to camera.
The screws are 01635-
350*2.

Screw driver

24

The top view of camera.

25

Install the Battery Cover
ASSY A140 as shown.
Install the Flex Cable
Main-LCD H600 on the
Rear Assembly.

26

Drive the screws 01635-
236*5 of Front Cover
ASSY A100.

Screw driver

14

«
...
14
15
16
17
18
...
»

Summary of Contents for PDR-M500


















































Reviews:

No comments

Related manuals for PDR-M500

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 100

Brand: Lasonic Pages: 1

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 61

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 119

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 232

Brand: Panasonic Pages: 130

Lumix DMC-GF1 C

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 62

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 189

Brand: Panasonic Pages: 195

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands