Toshiba HWS-1104H series Quick Reference Manual Download Page 28

Page: 28 / 64

Display Explanation

18: ZONE1, ZONE2

20: HOT WATER

Display

Description

Display

Description

Lights when floor heater or radiator

is connected (when the system has

floor heater or radiator).

Lights when hot water supply system is

connected (when the system has hot

water supply).

ZONE1 selected for Temperature

to be changed.

Lights when system configured to

have 2 zones.

ZONE2 selected for Temperature

to be changed.

HOT WATER selected for Temperature

to be changed.

Lights during heating or cooling

operation using the heat pump.

Lights when hot water supply operation

is performed by heat pump.

Lights when the internal heater is

energized during heating

operation.

Lights when the internal heater is

energized during hot water supply

operation.

Lights when heating is selected.

Lights during hot water supply operation.

Lights when cooling is selected.

Lights while hot water boost is activated.

Lights when the FROST

PROTECTION button is pressed

and goes out when the button is

pressed again.

Lights when the ANTI BACTERIA button

is pressed and goes out when the button

is pressed again.

Lights when Auto operation is

selected.

Lights when unit enters the data set

mode.

Displays heating/cooling set

temperature. (Heating: 20 to 55°C,

factory setting: Auto, cooling: 7 to

25°C) Goes out when Auto

operation is selected.

Displays hot water set temperature.

(40 to 75°C, factory setting: 65°C)

°C

Lights when the set temperature or

sensor's water temperature is

displayed with the 7-segment

indicator.

°C

Lights when the set temperature or

sensor's water temperature is displayed

with the 7-segment indicator.

Summary of Contents for HWS-1104H series

































































Search results

Summary of Contents for HWS-1104H series

Reviews:

Related manuals for HWS-1104H series

Brands by name

Popular brands

Toshiba HWS-1104H series, Quick Reference Manual

Search results

Summary of Contents for HWS-1104H series

Reviews:

Related manuals for HWS-1104H series

Brands by name

Popular brands