Toshiba HWS-1104H series Quick Reference Manual Download Page 27

Page: 27 / 64

Hydro Unit Remote Control

Buttons

1. TEMP. button:

Changes the set temperature for
each operation mode (ZONE1 /
ZONE2 / HOT WATER) by 1°C
step.

10. NIGHT button:

Controls the night set back
operation.

2. SCHEDULE
button:

Sets the current time and
scheduled weekly operation.

11. AUTO TEMP.
button:

Switches setting temperature
automatically according to outside
temperature. (Pressing this button
long changes the mode to data
setting mode).

3. TIME button:

Changes time for current time
setting and scheduled weekly
operation setting with ▼ and ▲
buttons.

12. OPERATE
MODE button:

Selects ZONE1 / ZONE2 operation
mode (heating or cooling).

4. SET button:

Determines the entered current
time setting and scheduled weekly
operation setting.

13. ZONE1, 2
button:

Turns on/off the zone (floor
heating/radiator/FCU) operation.

5. CL button:

Clears settings for the current time
and scheduled weekly operation.

14. ANTI BACTERIA
button:

Regularly increases the hot water
temperature in the tank for
sterilization. (Pressing this button
long changes the mode to data
setting mode).

6. DAY button:

Sets days of the week for current
time setting and scheduled weekly
operation setting.

15. HOT WATER
BOOST button:

Boosts boiling when high tapping
temperature is required temporarily.

7. STEP button:

Specifies switching STEP number
in a day for weekly schedule.

16. HOT WATER
button:

Turns on/off hot water operation.

8. TEST button:

Used for test run or service.

17. SELECT button:

Selects an operation mode when
changing the set temperature of
each operation mode.

9. FROST
PROTECTION
button:

Controls minimum operation for
unused period (going out,
absence,etc.) for anti freezing.

NOTE

Some functions are not provided depending on the system specification in use.

Summary of Contents for HWS-1104H series

































































Search results

Summary of Contents for HWS-1104H series

Reviews:

Related manuals for HWS-1104H series

Brands by name

Popular brands

Toshiba HWS-1104H series, Quick Reference Manual

Search results

Summary of Contents for HWS-1104H series

Reviews:

Related manuals for HWS-1104H series

Brands by name

Popular brands