Toshiba GD-1190 Service Manual Download Page 6

Page: 6 / 70

GD-1190 SPECIFICATIONS 1 - 1

[1] SPECIFICATIONS

Large item

Middle item

Small item

Sub item

Specifications

Communication
system

Electronic
transmission system

Electronic
transmission time

Less than 3 sec (Super G3 mode, 33600bps)
Less than 7 sec (G3 ECM mode, 14400bps)

Compression/
Extraction system

MH, MR, MMR, JBIG

MODEM speed

33600bps - 2400bps (Automatic fall-back)

Mutual communication

Super G3/G3

Used line

Public switched telephone network (PSTN), Private
branch exchange (PBX)

Used line number

1 line

Connection form

For 1 line of telephone;
• FAX machine
• External telephone

ECM

Yes

Transmission
functions

Transmission
operation

Items which can be
selected and
registered by user
when transmitting

• Specifying the destination number
• Resolution
• Density
• Transmission start time
• Polling receive
• Cover addition setting
• Send document scan system

Auto send function

Auto send function to a predetermined telephone
number

Application send
function

Chain dial

Max. 50 digits

Rapid key dial

Registration key

One-touch key

Number of items

Max. 18 items

Number of digits of
destination number

Max. 40 digits

Destination
registration name

Max. 20 characters

Retrieval characters

0 - 3 characters

Communication start
speed

Max. speed: 33600bps/ High speed: 14400bps/
Middle speed: 9600bps/ Low speed: 4800bps

International
communication mode

NO/ Mode 1/ Mode 2/ Mode 3

Transmission method

One-touch dial key

Speed dial

Number of items

100 items (Reduction number 00 - 99)

Number of digit of
destination number

40 digits

Destination
registration name

20 characters

Retrieval characters

0 - 3 characters

Communication start
speed

Max. speed: 33600bps/ High speed: 14400bps/
Meddle speed: 9600bps/ Low speed: 4800bps

International
communication mode

NO/ Mode 1/ Mode 2/ Mode 3

Transmission method

Speed dial key + (00 - 99) + Start key

Group dial

Registration key

One-touch dial key

Number of groups
which can be
registered

18 items (One-touch dial + Group dial)

Destination
registration name

20 characters

Number of stations
which can be
registered in one
group

Max. 100 stations in one group (Max. total items
which can be registered: 150 items)

Numbers which can be
registered

Destination numbers registered in one-touch dial and
speed dial, 10-key dial

Retrieval characters

0 - 3 characters

Transmission method

Group dial key

Address book send

Retrieval target

• Speed dial
• One-touch dial
• Group dial

Retrieval key

SEARCH key

Retrieval character

0 - 3 characters

ARFX9̲A1E.book 1 ページ２００４年１２月３日金曜日午後４時２２分

Summary of Contents for GD-1190







































































Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands

Toshiba GD-1190, Service Manual

Search results

Summary of Contents for GD-1190

Reviews:

Related manuals for GD-1190

Brands by name

Popular brands