Toshiba GD-1190 Service Manual Download | Manualshive

Page: 67 / 70

background image

LEAD-FREE SOLDER

The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.

The alphabet following the LF mark shows the kind of lead-free solder.

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread.

Never use conventional lead solder thread, which may cause a breakdown or an accident.

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.

If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.

If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.

Example:

5mm

Lead-Free

Solder composition
code (Refer to the
table at the right.)

<Solder composition code of lead-free solder>

Solder composition

Sn-Ag-Cu

Sn-Ag-Bi
Sn-Ag-Bi-Cu

Sn-Zn-Bi

Sn-In-Ag-Bi

Sn-Cu-Ni

Sn-Ag-Sb

Bi-Sn-Ag-P
Bi-Sn-Ag

a

b

z

i

n

s

p

Solder composition code

a

ARFX9̲A1E.book 1 ページ２００４年１２月３日金曜日午後４時２２分

«
...
65
66
67
68
69
...
»

Summary of Contents for GD-1190







































































Reviews:

No comments

Related manuals for GD-1190

Brand: Pfaff Pages: 56

Brand: Singer Pages: 24

Brand: easymaxx Pages: 2

Citymaster 2000

Brand: HAKO Pages: 186

Memory Craft 550E

Brand: Janome Pages: 84

MEMORY CRAFT 4900 QC

Brand: Janome Pages: 182

Brand: Sagem Pages: 2

Brand: Olivetti Pages: 64

Aria Quilting & Sewing Machine

Brand: Baby Lock Pages: 2

Brand: Singer Pages: 24

Minoltafax 1600e

Brand: Konica Minolta Pages: 127

Brand: JUKI Pages: 2

Brand: JUKI Pages: 4

Brand: Sandia Plastics Pages: 13

Brand: Vix Pages: 11

Brand: Silver Pages: 69

Advance QuickStar

Brand: Nilfisk-Advance Pages: 4

Brand: Artistic Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands